Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1436/45    Open in Passenger Side Air Mix Damper Position Sensor Circuit

DTC    B1437/-45    Short in Passenger Side Air Mix Damper Position Sensor Circuit

DTC    B1441/E45    Passenger Side Air Mix Damper Control Servomotor Circuit

for Preparation Click here


DESCRIPTION

This sensor detects the position of the air mix damper and sends appropriate signals to the A/C amplifier assembly. The position sensor is built into the air mix control servo motor. This adjusts the amount of air passing through the heater core after passing the No. 1 cooler evaporator sub-assembly and controls the temperature of the output air.

HINT:
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

E109300E01

DTC No.
DTC Detection Condition
Trouble Area
B1436/45
Open in passenger side air mix damper position sensor circuit
  1. No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))
  2. Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.
  3. Air conditioning control assembly
B1437/-45
Short in passenger side air mix damper position sensor circuit
  1. No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))
  2. Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.
  3. Air conditioning control assembly
B1441/E45
Passenger side air mix damper control servomotor circuit
  1. No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))
  2. Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.
  3. Air conditioning control assembly

WIRING DIAGRAM


E248914E01


INSPECTION PROCEDURE

NOTICE:
This DTC is stored even for damper link and damper lock, etc. Prior to inspection, confirm that there are no parts with mechanical problems.

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Operate the front passenger side temperature adjustment switch.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.


Air Conditioner 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Mix Damper Position
A/M Damp Pos-P)
Passenger side air mix damper position /
Min.: -32.68%, Max.: 133.33%
MAX. COLD: 0%
MAX. HOT: 110%
-
Air Mix Damper Target(P)
Passenger side air mix damper target position /
Min.: -32.68%, Max.: 133.33%
MAX. COLD: 0%
MAX. HOT: 110%
-


NG
Go to step 3
OK


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check the DTCs (Click here).

  1. Turn the GTS on.

OK:
DTC is not out put.



NG
REPLACE AIR CONDITIONING CONTROL ASSEMBLY
OK

END 

3.CHECK HARNESS AND CONNECTOR (NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
  1. Disconnect the D20 air conditioning control assembly.

  1. Disconnect the A28 No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)).

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance 
Tester Connection
Condition
Specified Condition
A28-1(VZ) - D20-13(S5)
Always
Below 1Ω
A28-3(GND) - D20-6(SG)
Always
Below 1Ω
A28-5(TP) - D20-3(TPPa)
Always
Below 1Ω
A28-6(COOL) - D20-12(AMCPa)
Always
Below 1Ω
A28-7(HOT) - D20-11(AMHPa)
Always
Below 1Ω
A28-1(VZ) - Body ground
Always
10 kΩ or higher
A28-3(GND) - Body ground
Always
10 kΩ or higher
A28-5(TP) - Body ground
Always
10 kΩ or higher
A28-6(COOL) - Body ground
Always
10 kΩ or higher
A28-7(HOT) - Body ground
Always
10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
  1. Remove the No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) .



  1. Potentiometer circuit inspection



      E249947E01
    1. Measure the resistance according to the value(s) in the table below.
      Standard resistance 
      Tester Connection
      Condition
      Specified Condition
      A28-1(VZ) - A28-3(GND)
      Always
      4.2 to 7.8 kΩ
      Text in Illustration 
      *a
      Component without harness connected
      (No. 4 air Conditioning radiator damper servo sub-assembly)



    2. Measure the resistance according to the value(s) in the table below.
      Standard resistance 
      Tester Connection
      Condition
      Specified Condition
      A28-1(VZ) - A28-5(TP)
      MAX. COOL position
      3.4 to 6.2 kΩ
      A28-1(VZ) - A28-5(TP)
      MAX. HOT position
      0.8 to 1.6 kΩ


      E249948E01

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      MAX. HOT
      *b
      MAX. COOL



    3. E108925E14
    4. As the arm of the air mix control servo motor moves from the COOL side to the HOT side, the resistance decreases gradually without interruption.

  1. Motor circuit inspection

    1. When the terminal 6 (COOL) of the connector A28 is connected to the battery positive terminal, and terminal 7 (HOT) of the connector A28 is connected to the battery negative terminal, confirm that the arm smoothly rotates from HOT to COOL.

      HINT:
      Because the arm does not automatically stop at servo unit inspection, at inspection, turn off the power supply near COOL

    2. When the terminal 7 (HOT) of the connector A28 is connected to the battery positive terminal, and terminal 6 (COOL) of the connector A28 is connected to the battery negative terminal, confirm that the arm smoothly rotates from COOL to HOT.

      HINT:
      Because the arm does not automatically stop at servo unit inspection, at inspection, turn off the power supply near HOT.



NG
REPLACE NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY