Home › Engine / Hybrid System › FA20 ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here



1. INSTALL INTAKE VALVE STEM OIL SEAL


    A146313E12
  1. Apply engine oil to new valve stem oil seals.
    Text in Illustration 
    *a
    for Intake
    *b
    for Exhaust
    *c
    Gray
    *d
    Light green

    NOTICE:
    1. Pay close attention to the colors when installing the oil seals.
    2. Installing the intake oil seal into the exhaust side or installing the exhaust oil seal to the intake side may cause installation problems later.



    A281043E01
  1. Using SST, push in the oil seals by hand.

    SST
    09201-41020  
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Place a cloth, etc. to avoid scratching the mating surface of the cylinder head during servicing.
    2. Do not tap SST with a plastic hummer to install the oil seals as it may damage the oil seals. Push in the oil seals by hand with SST.
    3. Do not install the oil seals at an angle.



2. INSTALL EXHAUST VALVE STEM OIL SEAL
  1. Using SST, push in the oil seals by hand.

    SST
    09201-41020  

    HINT:
    Use the same procedure as for the intake oil seals.



3. INSTALL INTAKE VALVE

NOTICE:
Place a cloth to avoid scratching the mating surface of the cylinder head during servicing.

  1. Set the valve spring seat, valve spring and retainer onto the cylinder head.

    HINT:
    Install the valve spring to the cylinder head with the narrow pitch end facing the valve spring seat.

  1. Apply engine oil to the valve stem and insert the valve into the valve guide bush.

    NOTICE:
    When inserting the valve into the valve guide bush, use special care not to damage the oil seal lip.

  1. Apply engine oil to the valve spring retainer locks.



    A278769E01
  1. Using SST, compress the valve spring and install the valve spring retainer locks.

    SST
    09202-70020   (09202-00010, 09202-01010, 09202-01020)



    A279609
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to tap the retainer.



4. INSTALL EXHAUST VALVE

NOTICE:
Place a cloth to avoid scratching the mating surface of the cylinder head during servicing.

  1. Set the valve spring seat, valve spring and retainer onto the cylinder head.

    HINT:
    Install the valve spring to the cylinder head with the narrow pitch end facing the valve spring seat.

  1. Apply engine oil to the valve stem and insert the valve into the valve guide bush.

    NOTICE:
    When inserting the valve into the valve guide bush, use special care not to damage the oil seal lip.

  1. Apply engine oil to the valve spring retainer locks.



    A279601E01
  1. Using SST, compress the valve spring and install the valve spring retainer locks.

    SST
    09202-70020   (09202-00010, 09202-01010, 09202-01020)



    A279610
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to tap the retainer.



5. INSTALL STUD BOLT


    A278768E01
  1. Install the 6 stud bolts to the cylinder heads.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    Text in Illustration 
    *a
    for Bank 1
    *b
    for Bank 2



6. INSTALL CHAIN COVER MOUNT BOLT


    A278767
  1. Install the chain cover mount bolt to the cylinder head sub-assembly LH.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }