Home › Engine / Hybrid System › FA20 LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the oil into a container.

  1. Clean and install the oil pan drain plug with a new oil pan drain plug gasket.

    Torque:
    42 N*m{ 425 kgf*cm , 31 ft.*lbf }



2. REMOVE OIL FILTER SUB-ASSEMBLY


A276044
  1. Remove any foreign matter and clean the installation surface of the engine.

  1. Using SST, remove the oil filter sub-assembly.

    SST
    09228-22020  



3. REMOVE OIL FILTER UNION


    A276915
  1. Remove the oil filter union.



4. INSTALL OIL FILTER UNION
  1. Install the oil filter union.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



5. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Remove any foreign matter and clean the inside and installation surface of the engine.

  1. Apply a light layer of engine oil to the seal rubber of a new oil filter sub-assembly.

  1. Tighten the oil filter sub-assembly by hand.

    NOTICE:
    Do not damage the seal rubber of the oil filter sub-assembly.

  1. Using SST, tighten the oil filter sub-assembly.

    SST
    09228-22020  

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



6. ADD ENGINE OIL
  1. Add new engine oil and install the oil filler cap.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    1. API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
    1. 0W-20
    2. 5W-30


    Standard Capacity:

    Item
    Capacity
    Drain and refill with oil filter change
    5.4 liters (5.7 US qts, 4.8 Imp. qts)
    Drain and refill without oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Dry fill
    6.3 liters (6.7 US qts, 5.5 Imp. qts)



7. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the connection point of the oil filter sub-assembly.



8. CHECK ENGINE OIL LEVEL
  1. Park the vehicle in a level place.

  1. With the engine turned off, check that the engine oil level is between the full level and low level marks.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not add engine oil above the full level mark.

    HINT:
    1. Check the oil level before the engine is started, or 5 minutes or more after the engine has been stopped (after engine warming).
    2. Check both sides of the dipstick and use the value obtained from the lower side oil level.