Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > Blower Motor Circuit

for Preparation Click here


DESCRIPTION

When the heater control sub-assembly is operated, the Heater relay will turn on to allow current to flow to the blower motor and then the motor will start rotating. Operating the heater control sub-assembly switches the current flow between the blower resistor and body ground, thus, shifting the operating speed of the blower motor.

WIRING DIAGRAM


E249476E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT HEATER BLOWER MOTOR RELAY
  1. Remove the heater blower motor relay.

  1. Inspect the heater blower motor relay .



NG
REPLACE HEATER BLOWER MOTOR RELAY
OK


2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
  1. Disconnect the A31 blower motor with fan sub-assembly connector.

  1. Inspect the blower motor with fan sub-assembly .



NG
REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A65-3 - A31-2
    Always
    Below 1 Ω
    A65-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT HEATER CONTROL SUB-ASSEMBLY
  1. Remove the heater control sub-assembly .

  1. Inspect the heater control sub-assembly .



NG
REPLACE HEATER CONTROL SUB-ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY - HEATER CONTROL SUB-ASSEMBLY)
  1. Disconnect the D23 heater control sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A65-2 - D23-10
    Always
    Below 1 Ω
    A65-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL SUB-ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-1 - D23-1
    Always
    Below 1 Ω
    A31-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (HEATER CONTROL SUB-ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D23-5(E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT BLOWER RESISTOR
  1. Remove the blower resister .

  1. Inspect the blower resistor .



NG
REPLACE BLOWER RESISTOR
OK


9.CHECK HARNESS OR CONNECTOR (HEATER CONTROL SUB-ASSEMBLY - BLOWER RESISTOR)
  1. Disconnect the A26 blower resister connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D23-3(M&M1) - A26-2(M&M1)
    Always
    Below 1 Ω
    D23-6(M2) - A26-3(M2)
    Always
    Below 1 Ω
    D23-3(M&M1) - Body ground
    Always
    10 kΩ or higher
    D23-6(M2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS OR CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BLOWER RESISTOR)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-1 - A26-1(H)
    Always
    Below 1 Ω
    A31-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-4(L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)