Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE

SPIRAL CABLE > INSPECTION

for Preparation Click here



1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
  1. Do not remove the steering sensor from the spiral cable sub-assembly.
  2. As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

  1. Remove the spiral cable with sensor sub-assembly from the vehicle .

  1. Visually check for defects with the spiral cable sub-assembly.

    1. The defects are as follows:

      1. Scratches
      2. Small cracks
      3. Dents
      4. Chips
      5. Cracks or other damage to the connector

        OK:
        No defects are found.

      If any of the defects is found, replace the spiral cable sub-assembly with a new one.



  1. Check the spiral cable sub-assembly.


    B311949E01


    Text in Illustration 
    *A
    for Dual Airbag System
    *B
    for Single Airbag System
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Color: Orange
    *c
    Color: Black
    -
    -

    1. Set the spiral cable sub-assembly to the center position .

    2. Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

      Standard Resistance:
      for Dual Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z7-2
      Always
      Below 1 Ω
      D52-2 - z7-1
      Always
      Below 1 Ω
      D52-3 - z6-1
      Always
      Below 1 Ω
      D52-4 - z6-2
      Always
      Below 1 Ω
      for Single Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z6-2
      Always
      Below 1 Ω
      D52-2 - z6-1
      Always
      Below 1 Ω

    3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

      Standard Resistance:
      for Dual Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z7-2
      Always
      Below 1 Ω
      D52-2 - z7-1
      Always
      Below 1 Ω
      D52-3 - z6-1
      Always
      Below 1 Ω
      D52-4 - z6-2
      Always
      Below 1 Ω
      for Single Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z6-2
      Always
      Below 1 Ω
      D52-2 - z6-1
      Always
      Below 1 Ω

    4. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

      Standard Resistance:
      for Dual Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z7-2
      Always
      Below 1 Ω
      D52-2 - z7-1
      Always
      Below 1 Ω
      D52-3 - z6-1
      Always
      Below 1 Ω
      D52-4 - z6-2
      Always
      Below 1 Ω
      for Single Airbag System: 
      Tester Connection
      Condition
      Specified Condition
      D51-1 - z4-3
      Always
      3 Ω or less
      D51-2 - z4-4
      Always
      3 Ω or less
      D51-2 - z5-6
      Always
      3 Ω or less
      D51-8 - z4-2
      Always
      3 Ω or less
      D51-8 - z5-1
      Always
      3 Ω or less
      D51-10 - z5-3
      Always
      3 Ω or less
      D51-11 - z5-4
      Always
      3 Ω or less
      D51-12 - z5-5
      Always
      3 Ω or less
      D52-1 - z6-2
      Always
      Below 1 Ω
      D52-2 - z6-1
      Always
      Below 1 Ω

      If the result is not as specified, replace the spiral cable with sensor sub-assembly.