Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Side)

SIDE AIRBAG SENSOR (for Front Side) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing. (Click here)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



3. REMOVE DOOR ARMREST COVER


    B313118E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 7 claws.

  1. Disengage the guides and remove the door armrest cover.
    Text in Illustration 
    *1
    Protective Tape



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313119E01
  1. Using a screwdriver with its tip wrapped in protective tape, open the cap.
    Text in Illustration 
    *1
    Protective Tape



    B313120
  1. Using a clip remover, disengage the clip.

  1. Remove the 3 screws.



    B313121
  1. Using a moulding remover, disengage the 10 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Disconnect each connector.

  1. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door glass weatherstrip inner.



    B313122E01
  1. Disconnect the front door lock remote control cable and the front door inside locking cable.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable
    *2
    Front Door Lock Remote Control Cable



5. REMOVE FRONT DOOR SERVICE HOLE COVER


    B314956
  1. Disconnect the outer rear view mirror sub-assembly connector.



    B314160
  1. Disconnect the front door lock assembly connector.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



6. REMOVE DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B311394E01
  1. Remove the nut and separate the door side airbag sensor from the front door panel.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

  1. Slide the outer housing to release the lock, and then disconnect the connector to remove the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    Text in Illustration 
    *1
    Outer Housing