Home › Drivetrain ยท TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the GTS on.

  6. Enter the following menus: "Powertrain / ECT / Data List" or "Body Electrical / Main Body / Data List".

  7. According to the display on the GTS, read the "Data List".

    "Powertrain / ECT / Data List" 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed /
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    Engine Speed
    Engine speed /
    Min.: 0 rpm, Max.: 16383.75 rpm
    550 to 800 rpm: Idling
    -
    Coolant Temp
    Engine coolant temperature /
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 215°C (419°F): sensor circuit shorted
    Engine Run Time
    Engine run time /
    Min.: 0 second,
    Max.: 65535 seconds
    Time after engine start
    -
    Battery Voltage
    Battery voltage /
    Min.: 0, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is
    1. ON: Depressed
    2. OFF: Released
    -
    A/C signal
    A/C signal status /
    ON or OFF
    A/C switch is:
    ON : OFF
    -
    #Codes (Include History)
    # of Codes /
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL ON Run Distance
    MIL ON run distance /
    Min.: 0 km (0 mile),
    Max.: 65535 km (40723 mile)
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON /
    Min.: 0 minute,
    Max.: 65535 minutes
    Equivalent to running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared /
    Min.: 0 minute,
    Max.: 65535 minutes
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared /
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Equivalent to time after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared /
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTCs cleared
    TC and TE1
    TC and TE1 terminals of DLC3 /
    ON or OFF
    -
    Active Test support data
    Engine Speed from EFI
    Engine speed /
    Min.: 0 rpm, Max.: 16383.75 rpm
    550 to 800 rpm: Idling
    -
    Coolant Temp from EFI
    Engine coolant temperature /
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    80 to 105°C (176 to 221°F): After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 140°C (284°F): sensor circuit shorted
    Throttle Position from EFI
    Throttle sensor position /
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on TCM
    Accel Position from EFI
    Absolute Accelerator Pedal Position /
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 54 to 86%: Accelerator pedal fully depressed
    -
    Received MIL from ECT
    MIL request status/
    ON : OFF
    MIL request is:
    ON : OFF
    -
    Shift Position Sig from ECT
    Received Shift Position Signal from ECT
    1st,2nd,3rd,4th,5th,6th,7th,8th
    Shift lever position is
    1. On D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. On M: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    SPD(NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12,750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever on N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    SPD(SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On P: ON
    2. Not on P: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On R: ON
    2. Not on R: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On N: ON
    2. Not on N: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Sport Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. Continuously shift to "+" (upshift): ON
    2. Release "+" (up-shift): OFF
    -
    Sport Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. Continuously shift to "-" (down-shift): ON
    2. Release "-" (down-shift): OFF
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever position is:
    1. M, "+" and "-": ON
    2. Not on M, "+" and "-": OFF
    -
    Snow Switch Status
    Pattern switch (ECT SNOW) status/
    ON or OFF
    Ignition switch is:
    Pushed: OFF
    ↓
    Pattern select switch (ECT SNOW) is:
    Pushed: ON
    ↓
    Pattern select switch (ECT SNOW) is:
    Pushed: OFF
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On D or M: ON
    2. Not on D or M: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    A/T Oil Temperature 1
    ATF temperature sensor No. 1 value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: 50 to 100°C (122 to 212°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor No. 1 circuit is opened or short circuited
    Lock Up
    Lock Up Status/
    ON or OFF
    Lock-up is
    1. Operating: ON
    2. Not operating: OFF
    -
    SL Solenoid Status
    Shift solenoid SL status/
    ON or OFF
    Shift solenoid SL is
    1. Operating: ON
    2. Not operating: OFF
    -
    Shift Status
    TCM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Shift lever position is
    1. On D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. On M: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    MT Down Shift Indication
    Shift indicator lamp down shift status/
    ON or OFF
    Shift indicator lamp is:
    ON : OFF
    -
    MT Up Shift Indication
    Shift indicator lamp up shift status/
    ON or OFF
    Shift indicator lamp is:
    ON : OFF
    -
    Snow or 2nd Mode
    Pattern select switch (SNOW) status/
    ON or OFF
    Ignition switch is:
    ON : OFF
    ↓
    Pattern select switch is:
    Pushed : ON
    ↓
    Pattern select switch is:
    Released : OFF
    -

    "Powertrain / ECT / Data List" 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is
    1. ON: Depressed
    2. OFF: Released
    -
    Shift P Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On P: ON
    2. Not on P: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    IG Power Supply Voltage
    IG Power Supply Voltage /
    Min.: 0, Max.: 21.4 V
    11 to 14 V: Idling
    -
    Shift Lock Solenoid
    Shift Lock Control Unit Assembly status/
    ON or OFF
    Shift Lock Control Unit Assembly is
    1. Operating: ON
    2. Not operating: OFF
    -


ACTIVE TEST

HINT:
Using GTS to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the GTS on.

  6. Enter the following menus: "Powertrain / ECT / Active Test" or "Body Electrical / Main Body / Active Test".

  7. According to the display on the GTS, perform the "Active Test".

    "Powertrain / ECT / Active Test" 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate the shift solenoid SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (S1)
    Operate the shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (S2)
    Operate the shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (S3)
    Operate the shift solenoid S3
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (S4)
    Operate the shift solenoid S4
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 50 km/h (30 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less
    Activate the Solenoid (SR)
    Operate the shift solenoid SR
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (SL1)
    Operate the shift solenoid SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Activate the Solenoid (SL2)
    Operate the shift solenoid SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever P or N position
    Connect the TC and TE1
    Connects and disconnects TC and TE1.
    (transitions into the fluid temperature detection mode)
    ON or OFF
    The MIL will not blink when "Connect the TC and TE1 / ON" is selected.

    "Body Electrical / Main Body / Active Test" 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Shift Lock
    Operate the shift lock
    ON or OFF
    -
    *: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in Active Test and HYDRAULIC TEST are different from each other.