Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the No.3 heater control sub-assembly is turned on, a magnetic clutch on signal is sent from the AC terminal of the ECM. Then, the engine room relay block assembly turns on to operate the magnetic clutch assembly.

WIRING DIAGRAM


E249944E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Date List.

  1. Check the value(s) by referring to the table below.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C SW Input
    A/C Switch Input
    OFF or ON
    ON: A/C switch on
    OFF: A/C switch off
    -

    OK:
    The display is as specified in the normal condition column.
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - POWER SOURCE)
  1. Disconnect the D21 No. 3 heater control sub-assembly connector.

  1. Measure the voltage according to the valve(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
D21-2(B) - Body ground
  1. Ignition switch on
  2. Blower switch: on
11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY
  1. Remove the No. 3 heater control sub-assembly .

  1. Inspect the No. 3 heater control sub-assembly .



NG
REPLACE NO. 3 HEATER CONTROL SUB-ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-17 - D21-3(A/C)
    Always
    Below 1 Ω
    D6-17 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NETWORK GATEWAY ECU 

5.READ VALUE USING GTS
  1. Enter the following menus: Powertrain / Engine and ETC / Date List.

  1. Check the value(s) by referring to the table below.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Pressure Normal SW
    Pressure Switch status
    ON or OFF
    ON
    -

    OK:
    The display is as specified in the normal condition column.
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

    OK:
    The display is as specified in the normal condition column.



B
Go to step 12
A


6.CHECK REFRIGERANT VOLUME
  1. Check the refrigerant volume (for HFC-134a(R134a)) .

  1. Check the refrigerant volume (for HFO-1234yf(R1234yf)) .



NG
CHARGE REFRIGERANT
OK


7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - POWER SOURCE)
E246513E03
  1. Disconnect the A7 air conditioner tube and accessory assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
A7-4(B) - Body ground
Ignition switch on
11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-2(E) - Body ground
Always
Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - HEATER RELAY)
E234483E01
  1. Remove the heater relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-1(AC) - 2
Always
Below 1 Ω
A7-1(AC) - Body ground
Always
10 kΩ or higher

Text in Illustration 
*1
Component without relay installed
(Engine Room Relay Block Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - ECM)
  1. Disconnect the A33 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-3(ACP) - A33-8(ACP)
Always
Below 1 Ω
A7-3(ACP) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
  1. Inspect the air conditioner tube and accessory assembly



NG
REPLACE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
OK

REPLACE ECM 

12.READ VALUE USING GTS
  1. Enter the following menus: Powertrain / Engine and ETC / Date List.

  1. Check the value(s) by referring to the table below.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    A/C Signal /
    OFF or ON
    A/C switch operated: ON (when switch is pressed)
    -
    A/C switch not operated: OFF (when switch is not pressed)

    OK:
    The display is as specified in the normal condition column.
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

    OK:
    The display is as specified in the normal condition column.



B
Go to step 15
A


13.INSPECT HEATER RELAY
  1. Remove the heater relay from the engine room relay block assembly.

  1. Inspect the heater relayClick here.



NG
REPLACE HEATER RELAY
OK


14.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)


    E234483E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch on
    11 to 14V

    Text in Illustration 
    *1
    Component without relay installed
    (Engine Room Relay Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (HEATER RELAY - COMPRESSOR WITH MAGNET CLUTCH)
  1. Disconnect the C17 compressor with magnet clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C17-1(MG+) - 3
    Always
    Below 1 Ω
    C17-1(MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.INSPECT COMPRESSOR WITH MAGNET CLUTCH
  1. Inspect the compressor with magnet clutch .



NG
REPLACE COMPRESSOR WITH MAGNET CLUTCH
OK


17.CHECK HARNESS AND CONNECTOR (HEATER RELAY - AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY)
  1. Disconnect the A7 air conditioner tube and accessory assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - A7-1(AC)
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK HARNESS AND CONNECTOR (HEATER RELAY - ECM)


    E234483E01
  1. Disconnect the A35 ECM connector.

  1. Measure the resistance according to the valve(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - A35-35(AC)
    Always
    Below 1 Ω
    1 - Body ground
    Always
    10kΩ or higher

    Text in Illustration 
    *1
    Component without relay installed
    (Engine Room Relay Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM