Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2271    Ignition Hold Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction in the IG1 drive circuit, IG2 drive circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2271
Either condition is met (1-trip detection logic*1):
  1. The IG1 or IG2 drive circuit in the certification ECU (smart key ECU assembly) is malfunctioning.
  2. The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.
  1. AM2 No. 2 fuse
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector
Turn the engine switch on (IG).

HINT:
To turn the engine switch on (IG), carry the key and press the engine switch twice with the shift lever in P or N*2 and the brake pedal*2 or clutch pedal*3 released.

  1. *1: Only output while a malfunction is present and the engine switch is on (IG)
  2. *2: for Automatic Transmission
  3. *3: for Manual Transmission

HINT:
  1. The IG1 and IG2 drive circuits activate the IG1 and IG2 relays.
  2. After the IG1 and IG2 drive circuits turn on, even if the certification ECU (smart key ECU assembly) operates incorrectly, the IG hold circuit maintains the engine switch on (IG) state.


Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The power source mode is not allowed to change to on (IG) (the engine cannot be started).
The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2271
Power Source Control
  1. IG1 Relay Monitor(Inside)
  2. IG2 Relay Monitor(Inside)
  3. Latch Circuit
Engine
  1. Ignition Status
-

WIRING DIAGRAM


B312725E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the D48 certification ECU (smart key ECU assembly) connector.


B264896E19


Text in Illustration 
*a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
  1. Measure the voltage according to the value(s) in the table below.


Standard Voltage:

Tester Connection
Switch Condition
Specified Condition
D41-6 (IG1D) - Body ground
Engine switch on (ACC) → Engine switch on (IG)
Below 1 V → 9 V or higher
D48-9 (IG2D) - Body ground
Engine switch on (ACC) → Engine switch on (IG)
Below 1 V → 9 V or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)