Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  7. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Brake Warning Light
    Brake warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Gear Position*
    Gear position information / "P,N", R, 1st-6th or Fail
    Actual gear position
    -
    Shift Lever Position*
    Shift lever position information / "P,N", R, D/M or Fail
    Actual shift lever position
    -
    Shift Information*
    Shift information / ON or OFF
    ON: During gear change
    -
    Inspection Mode
    Inspection mode / Other or Inspect
    Other: Normal mode
    Inspect: Inspection mode
    -
    Number of IG ON(Inspection)
    Number of times ignition switch turned to ON after entering inspection mode / Min.: 0, Max.: 255
    -
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V
    Brake pedal released: 0.20 to 0.40 V
    Reading increases when brake pedal is depressed
    Deceleration Sensor
    Acceleration sensor reading / Min.: -18.30 m/s2, Max.: 18.21 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Deceleration Sensor2
    Acceleration sensor 2 reading / Min.: -18.30 m/s2, Max.: 18.21 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s
    Vehicle stopped: 0 °/s
    Turning right: -128 to 0 °/s
    Turning left: 0 to 127 °/s
    -
    Steering Angle Sensor
    Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
    Turning left: Increases
    Turning right: Decreases
    -
    Lateral G
    Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During turning: Changes in proportion with acceleration
    Forward and Rearward G
    Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During acceleration/deceleration: Changes in proportion with acceleration
    Yaw Rate Value
    Yaw rate value / Min.: -128 °/s, Max.: 127 °/s
    -
    During turning: Changes in proportion with yaw
    Steering Angle Value
    Steering angle value / Min.: -3276.8°, Max.: 3276.7°
    -
    During steering operation: Changes in proportion with steering wheel rotation
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    Vehicle Speed
    Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FR Wheel Acceleration
    Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FL Wheel Acceleration
    Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RR Wheel Acceleration
    Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RL Wheel Acceleration
    Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FR Wheel ABS Ctrl Status
    Front wheel RH ABS control status / ON or OFF
    ON: During control
    -
    FL Wheel ABS Ctrl Status
    Front wheel LH ABS control status / ON or OFF
    ON: During control
    -
    RR Wheel ABS Ctrl Status
    Rear wheel RH ABS control status / ON or OFF
    ON: During control
    -
    RL Wheel ABS Ctrl Status
    Rear wheel LH ABS control status / ON or OFF
    ON: During control
    -
    FR Wheel EBD Ctrl Status
    Front wheel RH EBD control status / ON or OFF
    ON: During control
    -
    FL Wheel EBD Ctrl Status
    Front wheel LH EBD control status / ON or OFF
    ON: During control
    -
    RR Wheel EBD Ctrl Status
    Rear wheel RH EBD control status / ON or OFF
    ON: During control
    -
    RL Wheel EBD Ctrl Status
    Rear wheel LH EBD control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Ctrl Status
    TRC control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Engine Ctrl Status
    TRC engine control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Brake Ctrl Status
    TRC brake control status / ON or OFF
    ON: During control
    -
    FR Wheel VSC Ctrl Status
    Front wheel RH VSC control status / ON or OFF
    ON: During control
    -
    FL Wheel VSC Ctrl Status
    Front wheel LH VSC control status / ON or OFF
    ON: During control
    -
    RR Wheel VSC Ctrl Status
    Rear wheel RH VSC control status / ON or OFF
    ON: During control
    -
    RL Wheel VSC Ctrl Status
    Rear wheel LH VSC control status / ON or OFF
    ON: During control
    -
    Engine Revolutions
    Engine speed / Min.: 0 rpm, Max.: 65535 rpm
    Engine stopped: 0 rpm
    When engine speed is constant: No large fluctuations
    Real Engine Torque
    Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
    -
    -
    Accelerator Opening Angle %
    Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 100.0%
    When the accelerator pedal is released: 0.0%
    During accelerator pedal operation: Changes in proportion with the pedal movement
    Solenoid Relay
    ABS solenoid relay / ON or OFF
    ON: Solenoid relay on
    OFF: Solenoid relay off
    -
    ECB Motor Relay
    ABS motor relay / ON or OFF
    ON: Motor relay on
    OFF: Motor relay off
    -
    TRC(TRAC)/VSC Solenoid (SRM2)
    Master cut solenoid (SRM2) / ON or OFF
    ON: Operating
    -
    TRC(TRAC)/VSC Solenoid (SRM1)
    Master cut solenoid (SRM1) / ON or OFF
    ON: Operating
    -
    TRC(TRAC)/VSC Solenoid (SRC2)
    Master cut solenoid (SRC2) / ON or OFF
    ON: Operating
    -
    TRC(TRAC)/VSC Solenoid (SRC1)
    Master cut solenoid (SRC1) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR) / ON or OFF
    ON: Operating
    -
    IG1 Voltage Value
    IG1 voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    MT Voltage Value
    Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    TRC(TRAC)/VSC Off Mode
    TRC/VSC OFF mode / Normal, TRC(TRAC) OFF or VSC OFF
    Normal: Normal mode
    TRC(TRAC) OFF: TRC OFF mode
    VSC OFF: VSC OFF mode
    -
    Sports Mode
    VSC SPORT mode / Normal or Sports
    Normal: Normal mode
    Sports: VSC SPORT mode
    -
    Master Cylinder Pressure Sensor 1
    Master cylinder pressure sensor / Min.: -1.00 MPa, Max.: 23.99 MPa
    Brake pedal released: -1 to 0 MPa
    During brake pedal operation: Proportional to foot pedal pressure on brake
    Number of DTC
    Number of DTC recorded / Min.: 0, Max.: 255
    -
    -
    IG Voltage Value Decreased
    IG voltage value decrease detection / Error or Normal
    Error: Voltage low
    Normal: Normal
    -
    IG Voltage Value Increased
    IG voltage value increase detection / Error or Normal
    Error: Voltage high
    Normal: Normal
    -

    1. *: for Automatic Transmission


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON/OFF
    Observe combination meter assembly
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    TRC(TRAC) OFF Indicator Light
    TRC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe combination meter assembly
    Slip Indicator Light
    Slip indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Sports Mode Indicator Light
    VSC SPORT indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Motor Relay
    ABS motor relay
    Relay ON/OFF
    Operating sound of motor can be heard
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC(TRAC) Solenoid (SRMR)
    Master cut solenoid (SRM2)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC(TRAC) Solenoid (SRMF)
    Master cut solenoid (SRM1)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC(TRAC) Solenoid (SRCR)
    Master cut solenoid (SRC2)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC(TRAC) Solenoid (SRCF)
    Master cut solenoid (SRC1)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid
    ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH)
    Solenoid SRLR/SRLH/SRRR/SRRH/SFLR/SFLH/SFRR/SFRH
    Operating sound of each solenoid (clicking sound) can be heard
    VSC/TRC(TRAC) Solenoid
    Master cut solenoid (SRMR, SRMF, SRCR, SRCF, SPFL, SPFR, SMR, SMF)
    Solenoid SRMR/SRMF/SRCR/SRCF/SPFL/SPFR/SMR/SMF
    Operating sound of each solenoid (clicking sound) can be heard