Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

ENTRY AND START SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.



  5. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal*1
    Shift position (P) / OFF or ON
    OFF: Shift lever not in P
    ON: Shift lever in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The engine cannot be started when this item is "OFF".
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly (steering lock ECU) / OFF or ON
    OFF: Steering locked
    ON: Steering unlocked
    1. When the shift lever is in P*1 and the engine switch is off, if any door is opened or closed, the steering is locked.
    2. When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The engine cannot be started when the steering unlock signal is off.
    Stop Light Switch1*1
    State of brake pedal / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The engine cannot be started when this item is "OFF".
    3. When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
    Start Switch1
    Condition of engine switch contact 1 / OFF or ON
    OFF: Engine switch not pressed
    ON: Engine switch pressed
    1. If the engine switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the engine switch input signal is malfunctioning.
    Start Switch2
    Condition of engine switch contact 2 / OFF or ON
    OFF: Engine switch not pressed
    ON: Engine switch pressed
    1. Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.
    2. Behaves the same way as engine switch 1.
    Neutral SW/ Clutch SW*1
    Shift position (P, N) / OFF or ON
    OFF: Shift lever not in P or N
    ON: Shift lever in P or N
    1. Use this item to help determine if the park/neutral position switch is malfunctioning.
    2. The engine cannot be started when this item is "OFF".
    Neutral SW/ Clutch SW*2
    State of clutch pedal / OFF or ON
    OFF: clutch pedal released
    ON: clutch pedal depressed
    1. Use this item to help determine if the clutch position switch is malfunctioning.
    2. The engine cannot be started when this item is "OFF".
    Latch Circuit
    Condition of IG related backup circuit (IG hold circuit) / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    1. Displays in almost the same manner as the IG1 and IG2 relays.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG1 Relay Monitor(Outside)
    IG1 relay coil voltage monitor status / OFF or ON
    OFF: IG1 relay off
    ON: IG1 relay on
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG1 Relay Monitor(Inside)
    IG1 relay activation / OFF or ON
    OFF: IG1 relay off
    ON: IG1 relay on
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Outside)
    IG2 relay coil voltage monitor status / OFF or ON
    OFF: IG2 relay off
    ON: IG2 relay on
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Inside)
    IG2 relay activation / OFF or ON
    OFF: IG2 relay off
    ON: IG2 relay on
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    Starter Request Signal
    Condition of engine start command signal / OFF or ON
    OFF: Engine switch released after approximately 1 second elapses
    ON: Engine switch pressed and held while carrying electrical key transmitter sub-assembly with shift lever in P*1 and brake pedal*1 or clutch pedal*2 depressed
    1. When the engine cannot be started due to a start request signal malfunction, OFF is displayed.
    2. When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.
    ACC Relay Monitor
    ACC relay activation / OFF or ON
    OFF: ACC relay off
    ON: ACC relay on
    1. When the engine switch is on (IG), ON is displayed.
    2. While the engine is cranking, OFF is displayed.
    ACC Relay Cut Signal
    ACC relay cut signal / OFF or ON
    OFF: ACC relay on
    ON: ACC relay off
    -
    Engine Condition
    Condition of engine / Stop or Run
    Run: Engine running
    Stop: Engine stopped
    -
    Vehicle Speed Signal
    Vehicle moving or stationary / Stop or Run
    Run: Vehicle moving at 5 km/h (3 mph) or more
    Stop: Vehicle stopped
    -
    Power Supply Condition
    State of power supply / All OFF, IG1 ON or ACC ON, IG2 ON, ST ON,
    All OFF: Engine switch off (ACC and IG)
    ACC ON: Engine switch on (ACC)
    IG1 ON: Engine switch on (IG) (IG1 relay on)
    IG2 ON: Engine switch on (IG) (IG2 relay on)
    ST ON: Sending engine start request signal
    Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).
    Powertrain Type
    Vehicle identification / HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT, S&S-MMT
    Cnv-MT: Conventional M/T (M/T vehicle not equipped with hybrid system)
    Cnv-AT: Conventional CVT (CVT vehicle not equipped with hybrid system)
    Cnv-MMT: Conventional MMT (MMT vehicle not equipped with hybrid system)
    S&S-MT: Stop and start M/T (M/T vehicle not equipped with hybrid system)
    S&S-AT: Stop and start CVT (CVT vehicle not equipped with hybrid system)
    -
    IG1 Circuit
    IG1 relay coil circuit malfunction / OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item when determining whether the IG1 relay is malfunctioning.
    2. When the engine cannot be started due to an IG1 relay malfunction, OFF is displayed.
    IG2 Circuit
    IG2 relay coil circuit malfunction / OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item when determining whether the IG2 relay is malfunctioning.
    2. When the engine cannot be started due to an IG2 relay malfunction, NG is displayed.
    Starter SW Sig Mismatch
    Engine switch signal 1 and 2 do not match / No or Yes
    No: Switch normal
    Yes: Switch malfunctioning (engine switch signal 1 and 2 do not match)
    The engine can be started even if the result is Yes. However, emergency engine off while driving by pressing and holding the engine switch and, when the brakes are malfunctioning, emergency engine starting by pressing and holding the engine switch cannot be performed.
    Park Signal Mismatch*1
    Shift position (P) signal malfunction / No or Yes
    No: Signal normal
    Yes: Signal malfunction (CAN communication and direct line signal do not match)
    Even when Yes is displayed, it is still possible to turn the engine switch off (the power source mode will not be stuck in on (ACC) or on (IG)).
    Str Lock/Unlock Wait T-Out
    Steering lock or unlock malfunction / No or Yes
    No: Lock and unlock normal
    Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.)
    When the engine cannot be started due to a steering lock or unlock malfunction, Yes is displayed.
    Key Certif Wait T-Out
    Key verification malfunction / No or Yes
    No: Verification normal
    Yes: Verification error (detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching)
    When the engine cannot be started due to a key verification error, Yes is displayed.
    Number of Diagnosis Code
    Number of DTCs / 0 to 255
    -
    -

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

    1. Data List Display During Engine Switch Operation (for Automatic Transmission)


      B314083E01

      HINT:
      To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.
      *1: Without depressing the brake pedal, press the engine switch and check that the power source mode turns on (ACC).
      *2: Without depressing the brake pedal, press the engine switch and check that the power source mode turns on (IG).
      *3: Depress the brake pedal (the stop light switch turns on).
      *4: With the brake pedal depressed, press the engine switch and check that the engine starts.
      *5: Press the engine switch and check that the power source mode turns off.
      *6: Release the brake pedal.
      *7: Open a door.


    2. Data List Display During Engine Switch Operation (for Manual Transmission)


      B314084E01

      HINT:
      To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off.
      *1: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (ACC).
      *2: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (IG).
      *3: Depress the clutch pedal (the clutch start switch turns on).
      *4: With the clutch pedal depressed, press the engine switch and check that the engine starts.
      *5: Press the engine switch and check that the power source mode turns off.
      *6: Release the clutch pedal.
      *7: Open a door.


    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Certification ECU (smart key ECU assembly) IG power supply input status / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    When the engine switch is on (ACC), OFF is displayed.
    #Codes
    Number of DTCs / 0 to 255
    -
    -
    Immobiliser
    Engine immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset
    Set: Engine immobiliser set (engine start prohibited) (engine switch off)
    Unset: Engine immobiliser unset (engine start permitted) (engine switch on (ACC) or on (IG))
    1. When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) is part of the problem.
    2. The engine cannot be started when this item displays "Set"
    Steering Lock Sleep Cond
    Steering lock actuator assembly (steering lock ECU) sleep condition / No or Yes
    No: Sleep not available
    Yes: Sleep available
    -
    Steering Lock Start Cond
    Steering lock actuator assembly (steering lock ECU) wake up signal status / No or Yes
    No: Wake up signal not sent
    Yes: Wake up signal sent
    -
    Sensor Value
    History of malfunction of position sensor in steering lock actuator assembly (steering lock ECU) / OK or NG(Past)
    OK: History of malfunction for the lock or unlock sensor in the steering lock actuator assembly (steering lock ECU) does not exist.
    NG(Past): History of both the lock and unlock sensors in the steering lock actuator assembly (steering lock ECU) being on exists (Under normal operation, neither sensor is on).
    When this item displays "NG", the sensor inside the steering lock actuator assembly (steering lock ECU) may be malfunctioning, or there may be a mechanical malfunction.
    Power Supply Short
    History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock actuator assembly (steering lock ECU) / OK or NG (Past)
    OK: History of motor power source short does not exist
    NG (Past): History of motor power source short exists
    This item displays history when a malfunction exists in the circuit between the certification ECU (smart key ECU assembly) and the steering lock actuator assembly (steering lock ECU).
    Motor Driver Short
    History of malfunction (short) in the steering lock actuator assembly (steering lock ECU) motor circuit (DTC B2781 is stored) / OK or NG (Past)
    OK: History of short in the motor circuit does not exist
    NG (Past): History of short in the motor circuit exists
    History of a malfunction in the steering lock motor circuit in the steering lock actuator assembly (steering lock ECU).
    Lock/Unlock Receive
    History of receiving an unlock request signal / No or Yes
    No: History of receiving an unlock request signal does not exist
    Yes: History of receiving an unlock request signal exists
    -
    Lock Bar Stuck Error
    History of the steering wheel not being able to unlock properly when the steering lock operates for a certain amount of time / OK or NG (Past)
    OK: History of steering lock being stuck does not exist
    NG (Past): History of steering lock being stuck exists
    -
    Push Start Error
    History of push start malfunction due to steering lock actuator assembly (steering lock ECU) / OK or NG (Past)
    OK: History of push start malfunction does not exist
    NG (Past): History of push start malfunction exists
    -
    CPU Error
    Status of steering lock actuator assembly (steering lock ECU) /OFF or ON
    ON: Steering lock actuator assembly (steering lock ECU) is malfunction
    OFF: Steering lock actuator assembly (steering lock ECU) is normal
    -
    Engine Start Request
    Status of engine start permission signal determined by steering lock actuator assembly (steering lock ECU) and sent to certification ECU (smart key ECU assembly) / OK or NG
    OK: Signal received
    NG: Signal not received
    1. When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock actuator assembly (steering lock ECU) and has permitted fuel injection and engine combustion.
    2. The engine cannot be started when this item displays "NG".
    S Code Check
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When NG is displayed:
    1. S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    2. Steering wheel cannot be locked.
    3. Steering wheel cannot be unlocked (the engine cannot be started).
    L Code Check
    Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly (steering lock ECU) / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When NG is displayed:
    1. L code has not been registered for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU).
    2. Steering wheel cannot be locked.
    3. Steering wheel cannot be unlocked (the engine cannot be started).
    Unlock Request Receive
    Unlock request signal received state / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Within 10 sec. of turning the engine switch on (IG) or on (ACC), or of an engine start operation being performed
    NG: Engine switch on (IG) or on (ACC), or engine start operation not performed
    1. The engine cannot be started when an unlock request signal cannot be received.
    2. If Received (10 s) is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Lock Request Receive
    Lock request signal received state / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Lock request signal received for 10 sec. of any of the doors being opened with shift lever in P and engine switch off.
    NG: Except above
    If Received (10 s) is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    S Code Check(Past)
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past) / OK or NG(Past)
    OK: History of abnormal verification result does not exist
    NG(Past): History of abnormal verification result exists
    -
    L Code Check(Past)
    Verification result history between the ID code box (immobiliser code ECU) and steering lock actuator assembly (steering lock ECU) / OK or NG(Past)
    OK: History of abnormal verification result does not exist
    NG(Past): History of abnormal verification result exists
    -

    B317704E01

    HINT:
    To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.
    *1: Without depressing the brake pedal*5 or clutch pedal*6, press the engine switch and check that the power source mode turns on (ACC).
    *2: Without depressing the brake pedal*5 or clutch pedal*6, press the engine switch and check that the power source mode turns on (IG).
    *3: Press the engine switch and check that the power source mode turns off.
    *4: Release the brake pedal*5 or clutch pedal*6, open the driver side door and check that the steering locks.
    1. *5: for Automatic Transmission
    2. *6: for Manual Transmission


    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed / 0 to 16383 r/min
    Fluctuates in accordance with engine speed
    -
    Starter Signal
    Starter request signal monitor / OFF or ON
    OFF: Starting control switch off
    ON: Starting control switch on
    When malfunctioning, the engine will not crank.
    Starter Control
    Starter activation request / OFF or ON
    OFF: Starter activation not requested
    ON: Starter activation requested
    When malfunctioning, the engine will not crank.
    Shift SW Status (P Range)
    Condition of park/neutral position switch / OFF or ON
    OFF: Shift lever not in P
    ON: Shift lever in P
    When malfunctioning, the engine will not crank.
    Shift SW Status (N Range)
    Condition of park/neutral position switch / OFF or ON
    OFF: Shift lever not in N
    ON: Shift lever in N
    When malfunctioning, the engine will not crank.
    Starter Relay
    Starter relay voltage monitor / OFF or ON
    OFF: ST relay off
    ON: ST relay on
    OFF is displayed when the engine cannot crank.
    ST1
    Stop light switch assembly status / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -
    Ignition Status
    IG2 status / OFF or ON
    OFF: IG2 relay off
    ON: IG2 relay on
    -
    # Codes (Include History)
    Number of DTCs / 0 to 255
    -
    -
    1. *1: for Automatic Transmission

    B314085E01

    HINT:
    *: With the engine switch on (IG), the shift lever in P*1 or N*1and the brake pedal*1 or clutch pedal*2 depressed, press the engine switch and check that the engine starts.
    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Almost same as actual vehicle speed
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. According to the display on the GTS, perform the Active Test.


Power Source Control 
Tester Display
Test Part
Control Range
Diagnostic Note
P Supply for Steering Lock
Certification ECU (smart key ECU assembly)
OFF/ON

HINT:
OFF: Power is not supplied.
ON: Power is supplied.

When performing this Active Test, make sure the following condition is met:
The engine switch is on (IG).

Entry & Start 
Tester Display
Test Part
Control Range
Diagnostic Note
Power/Engine SW Light
Engine switch light
OFF/ON
When performing this Active Test, make sure the following condition is met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.