Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the GTS, read the Data List.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Touch Sensor*1
    Front door outside handle assembly (for driver side) (unlock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for driver side) (unlock sensor) not touched
    ON: Front door outside handle assembly (for driver side) (unlock sensor) touched
    1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
    P-Door Touch Sensor*1
    Front door outside handle assembly (for front passenger side) (unlock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for front passenger side) (unlock sensor) not touched
    ON: Front door outside handle assembly (for front passenger side) (unlock sensor) touched
    1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
    D-Door Trigger Switch*1
    Front door outside handle assembly (for driver side) (lock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for driver side) (lock sensor) not touched
    ON: Front door outside handle assembly (for driver side) (lock sensor) touched
    1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
    P-Door Trigger Switch*1
    Front door outside handle assembly (for front passenger side) (lock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for front passenger side) (lock sensor) not touched
    ON: Front door outside handle assembly (for front passenger side) (lock sensor) touched
    1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
    Tr/B-Door Unlock SW
    Back door opener switch assembly (unlock switch) / OFF or ON
    OFF: Back door opener switch not pushed
    ON: Back door opener switch assembly pushed
    1. Displays whether the back door opener switch is on or off.
    2. Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate.
    Ignition Switch
    Engine switch on (IG) / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    1. Displays whether the IG power source signal input is on or off.
    2. Use this Data List item to help determine the cause when all entry and start system/wireless functions do not operate.
    3. If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal*2 or clutch pedal*3, the engine switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the S code*4 or L code*5 stored in the certification ECU (smart key ECU assembly) and the code stored in the ID code box*4 or steering lock actuator assembly (steering lock ECU)*5 are compared, and if all codes match, the power source mode is considered on (IG) at that time.
    Unmatched Vehicle-ID
    Key No. (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    1. Always "NO" is displayed.
    2. No diagnostic function.
    No Response
    Communication response / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. Also, if there is electric wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Unmatch Code or Form
    Code format (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    1. Always "NO" is displayed.
    2. No diagnostic function.
    Key Low Battery
    Key battery depleted / No or Yes
    No: Key battery not depleted
    Yes: Key battery depleted
    The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.6 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
    Power Save Cnt 10 Min.
    Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more / 0 to 255
    Within range of 0 to 255
    If the electrical key transmitter sub-assembly is in the vehicle exterior detection area, communication is frequently performed between the vehicle and the electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the system stops operating. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.
    Power Save Cnt 5 Days
    Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to engine not being started for 5 days or more / 0 to 255
    Within range of 0 to 255
    -
    Power Save Cnt 14 Days
    Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger side door disabled) is activated due to engine not being started for 14 days or more / 0 to 255
    Within range of 0 to 255
    -
    ID Code Difference(Resp)
    ID code (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    1. Always "NO" is displayed.
    2. No diagnostic function.
    C Code Difference
    Challenge code (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is electric wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference (Resp)" and "C Code Difference" in the Data List).
    Other potential causes:
    1. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    ID Code Difference
    Wireless ID code (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference (Resp)" in the Data List.)
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Different Rolling Code
    Rolling code (incorrect or correct) / No or Yes
    No: Communication normal
    Yes: Communication malfunction
    The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different.
    Other potential causes:
    1. An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Auto Entry Cancel SW
    Entry cancel function setting / OFF or ON
    Mode status displayed
    OFF: Entry and start system not canceled
    ON: Entry and start system canceled
    The default setting for the entry cancel function is OFF. If the customer requests that the entry and start system functions (locking and unlocking the doors while carrying the key, etc.) be canceled, the setting can be changed through the customize function (Click here).
    Wireless Signal Encryption Support
    Wireless Signal Encryption Support / Yes or No
    Yes: Wireless signal encryption support
    No: Wireless signal encryption not support
    -
    Immobiliser
    Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset
    Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
    Unset: Engine immobiliser system unset (engine start permitted) (engine switch on (ACC) or on (IG))
    Problems may be caused by the following:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. Malfunctions in the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly) or engine switch.
    Short in Driver Side Door Oscillators Circuit
    Short in driver side door electrical key antenna circuit / OK or NG
    OK: Driver side door electrical key antenna circuit is normally
    NG: Driver side door electrical key antenna circuit is abnormally
    -
    Short in Front P Side Door Oscillators Circuit
    Short in passenger side door electrical key antenna circuit / OK or NG
    OK: Passenger side door electrical key antenna circuit is normally
    NG: Passenger side door electrical key antenna circuit is abnormally
    -
    Short in D Side Door Oscillators Circuit (Hist)
    Short in driver side door electrical key antenna circuit (history) / OK or NG (Hist)
    OK: Driver side door electrical key antenna circuit was normally
    NG (Hist): Driver side door electrical key antenna circuit was abnormally
    -
    Short in Fr P Side Door Oscillators Circuit (Hist)
    Short in passenger side door electrical key antenna circuit (history) / OK or NG (Hist)
    OK: Passenger side door electrical key antenna circuit was normally
    NG (Hist): Passenger side door electrical key antenna circuit was abnormally
    -
    Door Unlock Mode2
    Door Unlock Mode2 / All or Driver
    Customization status displayed
    -
    Ignition Available Area
    Ignition available area / Front or All
    Customization status displayed
    -
    Parking Wait Time
    Parking wait time / 0.5s, 1.5s, 2.5s, 5s
    Customization status displayed
    -
    Trunk Open Mode
    Luggage compartment door open mode / ON or OFF
    Customization status displayed
    -
    Key Low Battery Warning
    Low key battery warning / OFF or ON
    Customization status displayed
    -
    Touch Activation Over Threshold
    Consecutive entry lock operation / Active or Not Active
    Customization status displayed
    -
    Key Left in Vehicle Buz
    Key left in vehicle buzzer / OFF or ON
    Customization status displayed
    -
    Engine Start Indicator
    Engine start indicator / OFF or ON
    Customization status displayed
    -

    1. *1: Data from an actual vehicle provided for reference.
    2. *2: for Automatic Transmission
    3. *3: for Manual Transmission
    4. *4: w/ ID Code Box
    5. *5: w/o ID Code Box

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy light switch signal / OFF or ON
    OFF: Driver side door closed
    ON: Driver side door opened
    -
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal / LOCK or UNLOCK
    LOCK: Driver side door locked
    UNLOCK: Driver side door unlocked
    -
    P Door Courtesy SW
    Passenger side door courtesy light switch signal / OFF or ON
    OFF: Passenger side door closed
    ON: Passenger side door opened
    -
    P-Door Lock Pos SW
    Passenger side door unlock detection switch signal / LOCK or UNLOCK
    LOCK: Passenger side door locked
    UNLOCK: Passenger side door unlocked
    -
    Luggage Courtesy SW
    Luggage compartment door courtesy light switch signal / OFF or ON
    OFF: Luggage compartment door closed
    ON: Luggage compartment door open
    -
    IG SW
    Engine switch on (IG) / OFF or ON
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    ACC SW
    Engine switch on (ACC) / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (ACC)
    -
    Battery Power Supply Control Voltage
    Battery power supply control voltage / 0 to 21.4 V
    11 to 14 V
    -
    Battery Power Supply Back Up Voltage
    Battery power supply backup voltage / 0 to 21.4 V
    11 to 14 V
    -
    IG Power Supply Voltage
    IG power supply voltage / 0 to 21.4 V
    11 to 14 V
    -
    ACC Voltage
    ACC voltage / 0 to 21.4 V
    11 to 14 V
    -
    Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS-VSC-TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Almost the same as actual vehicle speed
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Entry & Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Overhead Tuner Power Supply ON
    Door control receiver
    OFF/ON
    -
    Power for D-Seat Sens
    Front door outside handle assembly (for driver side)
    OFF/ON
    -
    Power for P-Seat Sens
    Front door outside handle assembly (for passenger side)
    OFF/ON
    -
    Power/Engine SW Light
    Engine switch light
    OFF/ON
    When performing this Active Test, make sure the following condition is met:
    1. The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Door lock motor
    Unlock / Lock
    -
    D-Door Unlock
    Driver side door lock motor
    OFF / ON
    -
    Trunk and Back-Door Open
    Operate luggage door closer assembly motor
    OFF / ON
    -
    Wireless Buzzer
    Wireless door lock buzzer
    OFF / ON
    -
    Hazard
    Turn signal flasher assembly
    OFF / ON
    -