Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2286    Runnable Signal Malfunction

DTC    P0335    Crankshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2286
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1- trip detection logic*) do not match.
  1. AM2 No. 2 fuse
  2. Certification ECU (smart key ECU assembly)
  3. SFI system
  4. Wire harness or connector
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, and then start the engine. Make sure that the engine speed is 1000 rpm or more for 20 seconds or more after starting the engine.
P0335
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1- trip detection logic*) do not match.
  1. AM2 No. 2 fuse
  2. Certification ECU (smart key ECU assembly)
  3. SFI system
  4. Wire harness or connector
Wait for 10 seconds or more with the engine idling.
*: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. When the signal sent via either the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the engine switch is turned on (IG).)
  1. When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the engine switch has been turned off.
  1. When the signal sent via either direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.
  1. When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:
  2. If the following conditions are met, it is determined that the malfunction is not in CAN communication but in the direct line (TACH).
    1. When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.
    2. When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.
    If the following conditions are met, it is determined that the malfunction is not in the direct line (TACH) but in CAN communication.
    1. When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.
    2. When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.
    If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (TACH).
    1. When the engine switch is pressed, the engine stops cranking after 6 seconds.
    2. When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2286
P0335
Power Source Control
  1. Engine Condition
Engine
  1. Engine Speed
-

WIRING DIAGRAM


B268514E05


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING GTS (ENGINE CONDITION, ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Condition
    Condition of engine / Stop or Run
    Stop: Engine is stopped
    Run: Engine is running
    -

  1. Enter the following menus: Powertrain / Engine / Data List.

  1. According to the display on the GTS, read the Data List.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed / 0 to 16383 r/min
    Changes according to engine speed
    -

    OK:
    The Data List items change in accordance with the engine condition.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A35 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-17 (TACH) - A35-15 (TACH)
    Always
    Below 1 Ω
    D48-17 (TACH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the A35 ECM connector.



    B268627E06
  1. Reconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Check the signal waveform according to the condition(s) in the table below.

    OK:
    Tester Connection
    Condition
    Specified Condition
    D48-17 (TACH) - Body ground
    Engine is stopped
    No pulse generated
    Engine is running
    Pulse generated

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)