Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY


    B311335E01
  1. Before installing the front seat outer belt assembly, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 12° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 27°, check that the belt locks.
      Text in Illustration 
      *1
      Retractor
      *a
      Unlocked
      *b
      Locked
      *c
      27°
      If the result is not as specified, replace the front seat outer belt assembly.



2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B311334E01
  1. Engage the hook and install the front seat outer belt assembly with the 2 bolts.

    Torque:
    Bolt A:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    Bolt B:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



    B311336E01
  1. Connect the pretensioner connector.
    Text in Illustration 
    *1
    Pretensioner Connector
    *2
    Pretensioner Connector Lock

    NOTICE:
    When connecting any pretensioner connector, take care not to damage the pretensioner wire harness.

  1. Push in the lock to install the pretensioner connector.

    NOTICE:
    Securely lock the locking button.

  1. Install the shoulder anchor of the front seat outer belt assembly with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



3. INSTALL CENTER PILLAR GARNISH
  1. Engage the 2 guides and clip.

  1. Install the center pillar garnish LH with the 2 bolts and clip.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
  1. Install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the front seat outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  1. Install the floor anchor cover.



5. INSTALL REAR QUARTER TRIM FRONT GARNISH
  1. Engage the claw and clip.

  1. Install the rear quarter trim front garnish LH with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



6. INSTALL REAR WINDOW SIDE GARNISH
  1. Engage the guide and 2 clips.

  1. Install the rear window side garnish LH with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



7. INSTALL QUARTER TRIM LID SUB-ASSEMBLY
  1. Install the 2 lid cover clips from the quarter trim lid sub-assembly LH.

    NOTICE:
    If there is any damage, be sure to replace the lid cover clip with a new one.



    B321466E01
  1. Engage the 2 guides and 6 claws and install the quarter trim lid sub-assembly LH.
    Text in Illustration 
    *1
    Lid Cover Clip



8. INSTALL LUGGAGE COMPARTMENT TRIM COVER
  1. Engage the 8 clips install the quarter trim panel assembly LH.

  1. Install the clip.



9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B315249E01
  1. Align the alignment mark on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark

    NOTICE:
    After installation, check that the corners fit correctly.



10. INSTALL FRONT DOOR SCUFF PLATE
  1. Engage the 6 claws install the front door scuff plate LH.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



12. INSPECT SRS WARNING LIGHT
(Click here)