Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


  1. Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

    B315675E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-12 (+B) - E8 - 5 (GND)
    SB - B
    Power supply
    Always
    11 to 14 V
    E8-5 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F6-12 (+B) - F6-5 (GND)
    SB - B
    Power supply
    Always
    11 to 14 V
    F6-5 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-6 (WU) - E8-5 (GND)
    W-B - B
    Power window motor UP output
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch UP (Manual operation)
    Below 1 V
    E8-6 (WU) - E8-5 (GND)
    W-B - B
    Power window motor AUTO UP output
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    E8-7 (WD) - E8-5 (GND)
    LG - B
    Power window motor DOWN output
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch DOWN (Manual operation)
    Below 1 V
    E8-7 (WD) - E8-5 (GND)
    LG - B
    Power window motor AUTO DOWN output
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pushed DOWN (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    E8-8 (SN1) - E8-5 (GND)
    Y - B
    Hall IC in front power window regulator motor assembly LH input
    Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)
    E8-1 (SN2) - E8-5 (GND)
    GR - B
    Hall IC in front power window regulator motor assembly LH input
    Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F6-6 (WU) - F6-5 (GND)
    W-B - B
    Power window motor UP output
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch UP (Manual operation)
    Below 1 V
    F6-6 (WU) - F6-5 (GND)
    W-B - B
    Power window motor AUTO UP output
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    F6-7 (WD) - F6-5 (GND)
    LG - B
    Power window motor DOWN output
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch DOWN (Manual operation)
    Below 1 V
    F6-7 (WD) - F6-5 (GND)
    LG - B
    Power window motor AUTO DOWN output
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pushed DOWN (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    F6-8 (SN1) - F6-5 (GND)
    Y - B
    Hall IC in front power window regulator motor assembly RH input
    Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)
    F6-1 (SN2) - F6-5 (GND)
    GR - B
    Hall IC in front power window regulator motor assembly RH input
    Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)



  5. B399299E01
  6. waveform 1
    Measurement Condition 
    Item
    Content
    Tester Connection
    CH1: E8-8 (SN1) - E8-5 (GND)*1
    CH2: E8-1 (SN2) - E8-5 (GND)*1
    CH1: F6-8 (SN1) - F6-5 (GND)*2
    CH2 :F6-1 (SN2) - F6-5 (GND)*2
    Tool Setting
    5 V/DIV., 2 ms./DIV.
    Condition
    Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN

    1. *1: for LHD
    2. *2: for RHD


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


  1. Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

    B315675E03


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F6-12 (+B) - F6-5 (GND)
    SB - B
    Power supply
    Always
    11 to 14 V
    F6-5 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Bellow 1 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-12 (+B) - E8-5 (GND)
    SB - B
    Power supply
    Always
    11 to 14 V
    E8-5 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Bellow 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the F6*1 or E8*2 power window regulator switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F6-6 (WU) - F6-5 (GND)
    W-B - B
    Power window motor UP output
    Ignition switch ON, power window regulator switch off
    11 to 14 V
    Ignition switch ON, power window regulator switch UP (Manual operation)
    Bellow 1 V
    F6-6 (WU) - F6-5 (GND)
    W-B - B
    Power window motor AUTO UP output
    Ignition switch ON, front passenger side door power window fully open
    11 to 14 V
    Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled UP (Automatic operation)
    Bellow 1 V
    Ignition switch ON, front passenger side door power window fully closed
    11 to 14 V
    F6-7 (WD) - F6-5 (GND)
    LG - B
    Power window motor DOWN output
    Ignition switch ON, power window regulator switch off
    11 to 14 V
    Ignition switch ON, power window regulator switch DOWN (Manual operation)
    Bellow 1 V
    F6-7 (WD) - F6-5 (GND)
    LG - B
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger side door power window fully open
    11 to 14 V
    Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled DOWN (Automatic operation)
    Bellow 1 V
    Ignition switch ON, front passenger side door power window fully closed
    11 to 14 V
    F6-8 (SN1) - F6-5 (GND)
    Y - B
    Hall IC in front power window regulator motor assembly RH input
    Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)
    F6-1 (SN2) - F6-5 (GND)
    GR - B
    Hall IC in front power window regulator motor assembly RH input
    Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-6 (WU) - E8-5 (GND)
    W-B - B
    Power window motor UP output
    Ignition switch ON, power window regulator switch off
    11 to 14 V
    Ignition switch ON, power window regulator switch UP (Manual operation)
    Bellow 1 V
    E8-6 (WU) - E8-5 (GND)
    W-B - B
    Power window motor AUTO UP output
    Ignition switch ON, front passenger side door power window fully open
    11 to 14 V
    Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled UP (Automatic operation)
    Bellow 1 V
    Ignition switch ON, front passenger side door power window fully closed
    11 to 14 V
    E8-7 (WD) - E8-5 (GND)
    LG - B
    Power window motor DOWN output
    Ignition switch ON, power window regulator switch off
    11 to 14 V
    Ignition switch ON, power window regulator switch DOWN (Manual operation)
    Bellow 1 V
    E8-7 (WD) - E8-5 (GND)
    LG - B
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger side door power window fully open
    11 to 14 V
    Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled DOWN (Automatic operation)
    Bellow 1 V
    Ignition switch ON, front passenger side door power window fully closed
    11 to 14 V
    E8-8 (SN1) - E8-5 (GND)
    Y - B
    Hall IC in front power window regulator motor assembly LH input
    Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)
    E8-1 (SN2) - E8-5 (GND)
    GR - B
    Hall IC in front power window regulator motor assembly LH input
    Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN
    Pulse generation (See waveform 1)



  5. B399299E01
  6. waveform 1
    Item
    Content
    Tester Connection
    CH1: F6-8 (SN1) - F6-5 (GND)*1
    CH2: F6-1 (SN2) - F6-5 (GND)*1
    CH1: E8-8 (SN1) - E8-5 (GND)*2
    CH2: E8-1 (SN2) - E8-5 (GND)*2
    Tool Setting
    5 V/DIV., 2 ms./DIV.
    Condition
    Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN

    1. *1: for LHD
    2. *2: for RHD


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY


  1. Disconnect the E5*1 or F1*2 power window regulator motor assembly (for driver side) connector.

    1. *1: for LHD
    2. *2: for RHD

    B315684E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E5-5 (VCC) - E5-4 (SGD)
    W - R
    Power supply
    Always
    11 to 14 V
    E5-4 (SGD) - Body ground
    R - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-5 (VCC) - F1-4 (SGD)
    W - R
    Power supply
    Always
    11 to 14 V
    F1-4 (SGD) - Body ground
    R - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the E5*1 or F1*2 power window regulator motor assembly (for driver side) connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E5-1 (WU) - E5-4 (SGD)
    W-B - R
    Power window motor UP input
    Ignition switch ON, power window regulator master switch off
    11 to 14 V
    Ignition switch ON, power window regulator master switch UP (Manual operation)
    Below 1 V
    E5-1 (WU) - E5-4 (SGD)
    W-B - R
    Power window motor AUTO UP input
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    E5-3 (WD) - E5-4 (SGD)
    LG - R
    Power window motor DOWN input
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch DOWN (Manual operation)
    Below 1 V
    E5-3 (WD) - E5-4 (SGD)
    LG - R
    Power window motor AUTO UP input
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled DOWN (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-1 (WU) - F1-4 (SGD)
    W-B - R
    Power window motor UP input
    Ignition switch ON, power window regulator master switch off
    11 to 14 V
    Ignition switch ON, power window regulator master switch UP (Manual operation)
    Below 1 V
    F1-1 (WU) - F1-4 (SGD)
    W-B - R
    Power window motor AUTO UP input
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side door power window fully closed
    11 to 14 V
    F1-3 (WD) - F1-4 (SGD)
    LG - R
    Power window motor DOWN input
    Ignition switch ON, power window regulator master switch OFF
    11 to 14 V
    Ignition switch ON, power window regulator master switch DOWN (Manual operation)
    Below 1 V
    F1-3 (WD) - F1-4 (SGD)
    LG - R
    Power window motor AUTO UP input
    Ignition switch ON, driver side door power window fully open
    11 to 14 V
    Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled DOWN (Automatic operation)
    Below 1 V
    Ignition switch ON, driver side power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly (for driver side) may have a malfunction.


CHECK MAIN BODY ECU (NETWORK GATEWAY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B311513E04


Text in illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-1 (BECU) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    None - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    None - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-11 (GND) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-32 (+B) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Disconnect the D5 main body ECU (network gateway ECU) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D5-22 (ACC)* - Body ground
    W - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V

    1. *: w/ Entry and Start System

  5. Reinstall the main body ECU (network gateway ECU).

  6. Measure the voltage of the wire harness side connectors.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-13 (FPCY) - Body ground
    GR - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    3A-28 (FDCY) - Body ground
    V - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    D5-4 - Body ground
    LG - Body ground
    LIN communication signal
    Ignition switch ON
    Pulse generation

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-13 (FPCY) - Body ground
    GR - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    3A-28 (FDCY) - Body ground
    V - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    D5-4 - Body ground
    LG - Body ground
    LIN communication signal
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.