Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT SPEEDOMETER
  1. Check the operation.

    1. Using a speedometer tester (calibrated chassis dynamometer), check the speedometer indication according to the table below.

      Indicator Type: km/h (except Australia, New Zealand, United Kingdom) 
      Chassis Dynamometer Indication (km/h)
      Acceptable Range (km/h)
      20
      21.1 to 24.5
      40
      41.8 to 45.6
      60
      62.4 to 66.8
      80
      83.3 to 87.7
      100
      104.2 to 108.6
      120
      125.1 to 129.5
      140
      146.0 to 150.4
      160
      166.9 to 171.3
      180
      187.8 to 192.2
      200
      208.7 to 213.1
      220
      229.6 to 234.0
      240
      250.5 to 254.9

      Indicator Type: km/h (for Australia, New Zealand) 
      Chassis Dynamometer Indication (km/h)
      Acceptable Range (km/h)
      20
      21.1 to 24.5
      40
      41.4 to 45.2
      60
      61.6 to 66.0
      80
      82.1 to 86.5
      100
      102.6 to 107.0
      120
      123.1 to 127.5
      140
      143.6 to 148.0
      160
      164.1 to 168.5
      180
      184.6 to 189.0
      200
      205.1 to 209.5
      220
      225.6 to 230.0
      240
      246.1 to 250.5

      Indicator Type: MPH (for United Kingdom) 
      Chassis Dynamometer Indication (mph)
      Acceptable Range (mph)
      20
      20.8 to 23.2
      40
      41.6 to 44.2
      60
      62.5 to 65.1
      80
      83.4 to 86.0
      100
      104.3 to 106.9
      120
      125.2 to 127.8
      140
      146.1 to 148.7

      NOTICE:
      Tire wear, over inflation, or under inflation will cause errors.

    2. Check the deviation from the acceptable range of the speedometer indication.

      Reference:
      Less than 0.5 km/h (0.3 mph)

      HINT:
      If the indication is not as specified, go to the problem symptoms table (Click here).



2. INSPECT TACHOMETER
  1. Connect a tune-up tachometer, and start the engine.

  1. Compare the test results with the tachometer indications.

    Tune-up Tachometer Indication (rpm)
    Acceptable Range (rpm)
    1000
    933 to 1067
    2000
    1923 to 2077
    3000
    2913 to 3088
    4000
    3913 to 4088
    5000
    4913 to 5088
    6000
    5913 to 6088
    7000
    6913 to 7088
    8000
    7913 to 8088

    HINT:
    If the indication is not as specified, go to the Problem Symptoms Table (Click here).



3. INSPECT INDICATOR AND WARNING LIGHTS
  1. Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

    OK:

    Warning or Indicator Light
    Specified Condition
    LOW FUEL
    Warning or indicator light comes on for about 2 seconds after turning the ignition switch to ON.
    A/T OIL TEMP*1
    Warning or indicator light comes on for about 2 or 3 seconds after turning the ignition switch to ON.
    Leveling*2
    Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.
    Brake
    TRC OFF
    VSC OFF
    VSC SPORT
    SRS
    Warning light comes on for about 6 seconds after turning the ignition switch to ON.
    Charge
    The light goes off right after the engine starts.
    Oil pressure
    MIL (Check engine warning light)
    EPS
    SLIP
    The light goes off 3 minutes after starting the engine.
    ABS

    1. *1: for Automatic Transmission System
    2. *2: for HID Headlight