METER / GAUGE SYSTEM > ON-VEHICLE INSPECTION |
| 1. INSPECT SPEEDOMETER |
Check the operation.
Using a speedometer tester (calibrated chassis dynamometer), check the speedometer indication according to the table below.
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
| 20 | 21.1 to 24.5 |
| 40 | 41.8 to 45.6 |
| 60 | 62.4 to 66.8 |
| 80 | 83.3 to 87.7 |
| 100 | 104.2 to 108.6 |
| 120 | 125.1 to 129.5 |
| 140 | 146.0 to 150.4 |
| 160 | 166.9 to 171.3 |
| 180 | 187.8 to 192.2 |
| 200 | 208.7 to 213.1 |
| 220 | 229.6 to 234.0 |
| 240 | 250.5 to 254.9 |
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
| 20 | 21.1 to 24.5 |
| 40 | 41.4 to 45.2 |
| 60 | 61.6 to 66.0 |
| 80 | 82.1 to 86.5 |
| 100 | 102.6 to 107.0 |
| 120 | 123.1 to 127.5 |
| 140 | 143.6 to 148.0 |
| 160 | 164.1 to 168.5 |
| 180 | 184.6 to 189.0 |
| 200 | 205.1 to 209.5 |
| 220 | 225.6 to 230.0 |
| 240 | 246.1 to 250.5 |
| Chassis Dynamometer Indication (mph) | Acceptable Range (mph) |
| 20 | 20.8 to 23.2 |
| 40 | 41.6 to 44.2 |
| 60 | 62.5 to 65.1 |
| 80 | 83.4 to 86.0 |
| 100 | 104.3 to 106.9 |
| 120 | 125.2 to 127.8 |
| 140 | 146.1 to 148.7 |
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
| 20 | 21.1 to 24.5 |
| 40 | 41.3 to 45.1 |
| 60 | 61.4 to 65.8 |
| 80 | 81.8 to 86.2 |
| 100 | 102.2 to 106.6 |
| 120 | 122.6 to 127.0 |
| 140 | 143.0 to 147.4 |
| 160 | 163.4 to 167.8 |
| 180 | 183.8 to 188.2 |
| 200 | 204.2 to 208.6 |
| 220 | 224.6 to 229.0 |
| 240 | 245.0 to 249.4 |
| Chassis Dynamometer Indication (mph) | Acceptable Range (mph) |
| 10 | 10.5 to 12.7 |
| 20 | 20.6 to 23.0 |
| 40 | 40.9 to 43.5 |
| 60 | 61.3 to 63.9 |
| 80 | 81.7 to 84.3 |
| 100 | 102.1 to 104.7 |
| 120 | 117.5 to 125.1 |
| 140 | 137.1 to 145.5 |
Check the deviation from the acceptable range of the speedometer indication.
| 2. INSPECT TACHOMETER |
Connect a tune-up tachometer, and start the engine.
Compare the test results with the tachometer indications.
| Tune-up Tachometer Indication (rpm) | Acceptable Range (rpm) |
| 1000 | 933 to 1067 |
| 2000 | 1923 to 2077 |
| 3000 | 2913 to 3088 |
| 4000 | 3913 to 4088 |
| 5000 | 4913 to 5088 |
| 6000 | 5913 to 6088 |
| 7000 | 6913 to 7088 |
| 8000 | 7913 to 8088 |
| 3. INSPECT INDICATOR AND WARNING LIGHTS |
Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.
| Warning or Indicator Light | Specified Condition |
| Low Fuel*1 | Warning or indicator light comes on for about 2 seconds after turning the ignition switch to ON. |
| Water Temperature Hot*2 | |
| Master Warning*2 | |
| A/T Oil Temperature*1*3 | Warning or indicator light comes on for about 2 or 3 seconds after turning the ignition switch to ON. |
| Headlight Leveling | Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON. |
| Brake | |
| TRC OFF | |
| VSC OFF | |
| Tire Pressure*4 | |
| TRACK | |
| SRS Airbag | Warning light comes on for about 6 seconds after turning the ignition switch to ON. |
| Charge | The light goes off right after the engine starts. |
| Oil pressure | |
| MIL (Check engine warning light) | |
| EPS | |
| Slip | The light goes off 3 minutes after starting the engine. |
| ABS |