OUTER REAR VIEW MIRROR > INSPECTION |
| 1. INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH |
Check the operation of the mirror surface.
![]() |
Disconnect the outer rear view mirror sub-assembly RH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 3 (MR+) Battery negative (-) → Terminal 8 (MV) | Turns upward |
| Battery positive (+) → Terminal 8 (MV) Battery negative (-) → Terminal 3 (MR+) | Turns downward |
| Battery positive (+) → Terminal 7 (MH) Battery negative (-) → Terminal 3 (MR+) | Turns left |
| Battery positive (+) → Terminal 3 (MR+) Battery negative (-) → Terminal 7 (MH) | Turns right |
| *a | Component without harness connected (Outer Rear View Mirror Sub-assembly RH) |
Check the operation of the retractable mirror (w/ Mirror Retract Switch).
![]() |
Disconnect the outer rear view mirror sub-assembly RH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
| Tester Connection | Condition | Specified Condition |
| Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) | Position between forward position (A) and driving position (C) | Moves from (B) to forward position (A) |
| Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) | Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) | Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) | Retracted position (E) | Moves from (E) to driving position (C) |
| *a | (A) Forward Position |
| *b | (B) |
| *c | (C) Driving position |
| *d | (D) |
| *e | (E) Retracted Position |
| *f | Component without harness connected (Outer Rear View Mirror Sub-assembly RH) |
Check the operation of the mirror heater (w/ Mirror Heater).
Disconnect the outer rear view mirror sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (+) - 10 (-) | 25°C (75°F) | 9.6 to 14.4 Ω |
Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.
| 2. INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH |
Check the operation of the mirror surface.
![]() |
Disconnect the outer rear view mirror sub-assembly LH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 3 (ML+) Battery negative (-) → Terminal 8 (MV) | Turns upward |
| Battery positive (+) → Terminal 8 (MV) Battery negative (-) → Terminal 3 (ML+) | Turns downward |
| Battery positive (+) → Terminal 7 (MH) Battery negative (-) → Terminal 3 (ML+) | Turns left |
| Battery positive (+) → Terminal 3 (ML+) Battery negative (-) → Terminal 7 (MH) | Turns right |
| *a | Component without harness connected (Outer Rear View Mirror Sub-assembly LH) |
Check the operation of the retractable mirror (w/ Mirror Retract Switch).
![]() |
Disconnect the outer rear view mirror sub-assembly LH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
| Tester Connection | Condition | Specified Condition |
| Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) | Position between forward position (A) and driving position (C) | Moves from (B) to forward position (A) |
| Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) | Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) | Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 66 (MRL) Battery negative (-) → Terminal 2 (MFL) | Retracted position (E) | Moves from (E) to driving position (C) |
| *a | (A) Forward Position |
| *b | (B) |
| *c | (C) Driving position |
| *d | (D) |
| *e | (E) Retracted Position |
| *f | Component without harness connected (Outer Rear View Mirror Sub-assembly LH) |
Check the operation of the mirror heater (w/ Mirror Heater).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (+) - 10 (-) | 25°C (75°F) | 9.6 to 14.4 Ω |
Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.