Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH

OUTER MIRROR SWITCH > INSPECTION

for Preparation Click here



1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD)


    B310943E01
  1. Check the switch functions.

    1. Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      Mirror Select Switch
      *2
      Mirror Surface Adjust Switch
      *3
      Mirror Retract Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      Standard Resistance (for left side):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 14 (ML+)
      10 (VL) - 7 (E)
      UP
      Below 1 Ω
      1 (B) - 10 (VL)
      14 (ML+) - 7 (E)
      DOWN
      Below 1 Ω
      1 (B) - 8 (HL)
      14 (ML+) - 7 (E)
      LEFT
      Below 1 Ω
      1 (B) - 14 (ML+)
      8 (HL) - 7 (E)
      RIGHT
      Below 1 Ω

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 12 (MR+)
      11 (VR)- 7 (E)
      UP
      Below 1 Ω
      1 (B) - 11 (VR)
      12 (MR+) - 7 (E)
      DOWN
      Below 1 Ω
      1 (B) - 9 (HR)
      12 (MR+) - 7 (E)
      LEFT
      Below 1 Ω
      1 (B) - 12 (MR+)
      9 (HR) - 7 (E)
      RIGHT
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch assembly.

  1. Check the mirror retract switch. (w/ Mirror Retract Switch)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 6 (MFR)
      3 (MRR) - 7 (E)
      Mirror retract switch retract position
      Below 1 Ω
      1 (B) - 3 (MRR)
      6 (MFR) - 7 (E)
      Mirror retract switch return position

      If the result is not as specified, replace the outer mirror switch assembly.



2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD)


    B314946E01
  1. Check the switch functions.

    1. Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      Mirror Select Switch
      *2
      Mirror Surface Adjust Switch
      *3
      Mirror Retract Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      Standard Resistance (for left side):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 14 (ML+)
      10 (VL) - 7 (E)
      UP
      Below 1 Ω
      1 (B) - 10 (VL)
      14 (ML+) - 7 (E)
      DOWN
      Below 1 Ω
      1 (B) - 8 (HL)
      14 (ML+) - 7 (E)
      LEFT
      Below 1 Ω
      1 (B) - 14 (ML+)
      8 (HL) - 7 (E)
      RIGHT
      Below 1 Ω

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 12 (MR+)
      11 (VR)- 7 (E)
      UP
      Below 1 Ω
      1 (B) - 11 (VR)
      12 (MR+) - 7 (E)
      DOWN
      Below 1 Ω
      1 (B) - 9 (HR)
      12 (MR+) - 7 (E)
      LEFT
      Below 1 Ω
      1 (B) - 12 (MR+)
      9 (HR) - 7 (E)
      RIGHT
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch assembly.

  1. Check the mirror retract switch. (w/ Mirror Retract Switch)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 6 (MFR)
      3 (MRR) - 7 (E)
      Mirror retract switch retract position
      Below 1 Ω
      1 (B) - 3 (MRR)
      6 (MFR) - 7 (E)
      Mirror retract switch return position

      If the result is not as specified, replace the outer mirror switch assembly.