Home › Power Source / Network › FA20 BATTERY / CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR HOLDER WITH RECTIFIER


    A277220
  1. Install the generator holder with rectifier with the 3 bolts.



    A277219
  1. Install the terminal with the nut.

    Torque:
    8.9 N*m{ 91 kgf*cm , 79 in.*lbf }



    A277218
  1. Install the terminal cover.



2. INSTALL BRUSH


    A281731E01
  1. Using a soldering iron, install the 2 brushes to the brush holder assembly.
    Text in Illustration 
    *1
    Soldering iron
    *2
    Solder



    A277216
  1. Install the cover B to the brush holder assembly.



    A277215
  1. Install the cover A to the brush holder assembly.



3. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A277214E01
  1. Install the generator brush holder assembly with the 4 bolts.

    Torque:
    Bolt A:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
    Bolt B:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



    A277221E01
  1. While pushing the 2 brushes into the generator rear end cover, insert a 1.0 mm (0.0394 in.) pin into the generator rear end cover.

    NOTICE:
    Remove the pin after reassembling the generator.

    Text in Illustration 
    *1
    Pin 1.0 mm (0.0394 in.)



4. INSTALL GENERATOR COIL ASSEMBLY


    A277213
  1. Install the generator coil assembly with the 6 bolts.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



5. INSTALL GENERATOR ROTOR BEARING


    A279037
  1. Using SST and a press, press in a new generator rotor bearing.

    SST
    09632-36010  
    09820-36010  



6. INSTALL GENERATOR DRIVE END FRAME BEARING


    A284676E01
  1. Using SST and a press, press in a new generator drive end frame bearing.

    SST
    09950-60010   (09951-00520)
    09950-70010   (09951-07100)



    A277207
  1. Install the bearing retainer with the 4 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



7. INSTALL GENERATOR DRIVE END FRAME ASSEMBLY


    A277206
  1. Install the generator drive end frame assembly to the generator rotor assembly.



8. INSTALL GENERATOR PULLEY


    A277204E01
  1. Mount the generator in a vise between aluminum plates.
    Text in Illustration 
    *1
    Aluminium plate



    A277205
  1. Install the generator pulley with the nut.

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf }



9. INSTALL GENERATOR REAR END COVER


    A279034E01
  1. using the heat gun, heat the generator rear end cover.

    Heating Temperature:
    Item
    Temperature
    Generator Rear End Cover
    50 to 60°C (122 to 140°F)

    Text in Illustration 
    *1
    Heat gun

  1. Install the generator rear end cover.

  1. Pull out the pin of the generator rear end cover.



    A277202
  1. Install the 4 through bolts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }