Home › Engine / Hybrid System › FA20 ENGINE CONTROL › CAMSHAFT OIL CONTROL VALVE

CAMSHAFT OIL CONTROL VALVE > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Exhaust Side of Bank 2)
  1. Install the back-up ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.

  1. Install the camshaft timing oil control valve with the 2 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

    NOTICE:
    1. If a component has been dropped or subjected to a strong impact, replace it.
    2. Make sure that the O-ring is not damaged or does not jump out of position during installation.

  1. Connect the camshaft timing oil control valve connector.



2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Intake Side of Bank 2)
  1. Install the back-up ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.

  1. Install the camshaft timing oil control valve with the 2 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

    NOTICE:
    1. If a component has been dropped or subjected to a strong impact, replace it.
    2. Make sure that the O-ring is not damaged or does not jump out of position during installation.

  1. Connect the camshaft timing oil control valve connector.



3. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
  1. Install the air cleaner cap with air cleaner hose with the 3 blots.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the air cleaner cap with air cleaner hose with the 2 hose clamps.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Connect the No. 2 ventilation hose.

  1. Connect the mass air flow meter connector.

  1. Engage the wire harness clamp and install the wire harness to the air cleaner cap.



4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Exhaust Side of Bank 1)
  1. Install the back-up ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.

  1. Install the camshaft timing oil control valve with the 2 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

    NOTICE:
    1. If a component has been dropped or subjected to a strong impact, replace it.
    2. Make sure that the O-ring is not damaged or does not jump out of position during installation.

  1. Connect the camshaft timing oil control valve connector.



5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Intake Side of Bank 1)
  1. Install the back-up ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.

  1. Install the camshaft timing oil control valve with the 2 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

    NOTICE:
    1. If a component has been dropped or subjected to a strong impact, replace it.
    2. Make sure that the O-ring is not damaged or does not jump out of position during installation.

  1. Connect the camshaft timing oil control valve connector.



6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL