Home › Drivetrain ยท CLUTCH › CLUTCH PEDAL (for LHD)

CLUTCH PEDAL (for LHD) > INSTALLATION

for Preparation Click here



1. INSTALL CLUTCH PEDAL PAD
  1. Install the clutch pedal pad to the clutch pedal sub-assembly.



2. INSTALL NO. 1 CLUTCH PEDAL CUSHION
  1. Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.



3. INSTALL CLUTCH PEDAL STOPPER
  1. Install the clutch pedal stopper to the clutch pedal support sub-assembly.



4. INSTALL CLUTCH PEDAL SUB-ASSEMBLY


    C262742
  1. Apply MP grease to the 2 clutch pedal bushes.
    Text in Illustration 
    V100135
    MP grease

  1. Install the clutch pedal sub-assembly and 2 clutch pedal bushes to the clutch pedal support sub-assembly.

  1. Using a pin punch (3 mm (0.118 in.)) and a hammer, align the clutch pedal lever sub-assembly hole and the clutch pedal sub-assembly hole, and insert the straight pin from above.



5. INSTALL CLUTCH PEDAL SPRING
  1. Install the 2 bushes to the clutch pedal sub-assembly and clutch pedal support sub-assembly.



    C261054
  1. Apply MP grease to the assist rod A, assist rod B and clutch pedal spring.
    Text in Illustration 
    V100135
    MP grease

  1. Install the assist rod A, assist rod B, clutch pedal spring and assist bush to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.



    C261055
  1. Apply MP grease to the 2 clevis pins.
    Text in Illustration 
    V100135
    MP grease

  1. Install the 2 clevis pins and 2 E-rings.

    HINT:
    Install the clevis pin from the left side of the vehicle.



6. INSTALL CLUTCH SWITCH ASSEMBLY
  1. Install the clutch switch assembly to the clutch pedal support sub-assembly with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



7. INSTALL CLUTCH START SWITCH ASSEMBLY
  1. Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the clutch start switch connector.



    C263918E01
  1. With the clutch pedal fully depressed, check that the clearance shown in the illustration is as specified.
    Text in Illustration 
    *a
    Clearance

    Standard clearance:
    3.5 to 4.0 mm (0.138 to 0.157n.)

    HINT:
    Do not turn the clutch start switch assembly.



8. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY


    C262634E01
  1. Insert the hook on the clutch pedal support sub-assembly into the vehicle panel.
    Text in Illustration 
    *1
    Hook

  1. Install the clutch pedal support sub-assembly to the vehicle with the 4 nuts and 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the clutch master cylinder assembly with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Apply MP grease to the new clevis pin.

  1. Install the clutch master cylinder push rod clevis to the clutch pedal lever sub-assembly with the clevis pin and a clip.

    HINT:
    Install the clevis pin from the left side of the vehicle.

  1. Apply MP grease to the push rod pin.

  1. Install the brake master cylinder push rod clevis with the push rod pin and a clip.

    HINT:
    Install the push rod pin from the left side of the vehicle.

  1. Connect the connector and engage the wire harness clamp.

  1. Connect the 3 connectors.



9. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    C262632E01
  1. Install the steering intermediate shaft assembly to the steering column assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



10. INSPECT AND ADJUST CLUTCH PEDAL
(Click here)


11. INSPECT CLUTCH SWITCH ASSEMBLY


    C262743E01
  1. Without depressing the clutch pedal sub-assembly, check that there is no clearance between the clutch switch shaft and the clutch pedal stopper.
    Text in Illustration 
    *a
    No Clearance



12. INSTALL STEERING CONTROL ECU
(Click here)


13. INSPECT CLUTCH START SYSTEM
  1. Check that the engine does not start when the clutch pedal is released.

  1. Check that the engine starts when the clutch pedal is fully depressed.
    If necessary, replace or adjust the clutch start switch assembly.