Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE ASPIRATOR (for Automatic Air Conditioning System)


    E250772
  1. Disengage the 2 claws and remove the aspirator with aspirator pipe as a unit.



2. REMOVE ASPIRATOR PIPE (for Automatic Air Conditioning System)


    E250773
  1. Remove the aspirator pipe.



3. REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    E250744
  1. Remove the 2 screws and No. 1 air conditioning radiator damper servo sub-assembly.



4. REMOVE NO. 5 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250782
  1. Remove the 2 screws and No. 5 air conditioning radiator damper servo sub-assembly.

    NOTICE:
    When re-using the No. 5 air conditioner damper servo sub-assembly, set the temperature adjustment dial to MAX COOL before removing the sub-assembly, and then wait for 30 seconds before beginning work.



5. REMOVE HEATER COVER (for Automatic Air Conditioning System)


    E250745
  1. Remove the 3 screws and heater cover.



6. REMOVE HEATER COVER (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



7. REMOVE HEATER COVER (w/o Airbag System)

HINT:
Use the same procedure as for the automatic air conditioning system.



8. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250746
  1. Remove the screw and the clamp.



    E250747
  1. Remove the heater radiator unit sub-assembly as shown in the illustration.



9. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



10. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



11. REMOVE AIR FILTER CASE


    E250748
  1. Disengage the 2 claws and remove the air filter case.



12. REMOVE CLEAN AIR FILTER


    E253432
  1. Remove the clean air filter as shown in the illustration.



13. REMOVE COOLING UNIT CASE


    E252240
  1. Remove the 2 screws.

  1. Disengage the 4 claws and remove the cooling unit case.



14. REMOVE COOLER EXPANSION VALVE (for Automatic Air Conditioning System)


    E250751
  1. Remove the gasket.



    E250765
  1. Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and cooler expansion valve.



    E250766
  1. Remove the 2 O-rings from the evaporator pipe.



15. REMOVE COOLER EXPANSION VALVE (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



16. REMOVE COVER


    E250752
  1. Remove the 3 screws.

  1. Disengage the 2 claws and remove the cover.



17. REMOVE NO. 1 COOLER UNIT DRAIN HOSE


    E250753
  1. Remove the No. 1 cooler unit drain hose.



18. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY


    E250754
  1. Remove the 2 screws and remove the No. 1 air duct sub-assembly.



19. REMOVE BLOWER MOTOR WITH FAN SUB-ASSEMBLY


    E250755
  1. Remove the 3 screws and remove the blower motor with fan sub-assembly.



20. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY


    E246467
  1. Remove the 3 screws and remove the No. 2 air duct sub-assembly.



21. REMOVE NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250767
  1. Remove the 2 screws and remove the No. 4 air conditioning radiator damper servo sub-assembly.

    NOTICE:
    When re-using the No. 4 air conditioner damper servo sub-assembly, set the temperature adjustment dial to MAX COOL before removing the sub-assembly, and then wait for 30 seconds before beginning work.



22. REMOVE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250768
  1. Remove the 3 screws and remove the No. 3 air conditioning radiator damper servo sub-assembly.



23. REMOVE AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)


    E250775
  1. Disengage the 3 claws and remove the air inlet damper control cable sub-assembly.

    NOTICE:
    Hold the control cable and remove the drive gear on the unit side slowly, without pulling it.



24. REMOVE AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the manual air conditioning system.



25. REMOVE HEATER CONTROL CABLE SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250776
  1. Disengage the 3 claws and remove the heater control cable sub-assembly.

    NOTICE:
    Hold the control cable and remove the drive gear on the unit side slowly, without pulling it.



26. REMOVE HEATER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the manual air conditioning system.



27. REMOVE COOLING UNIT CASE SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250758
  1. Disengage the clamp.



    E246468
  1. Remove the 7 screws.

  1. Disengage the 2 claws and remove the cooling unit case sub-assembly.



28. REMOVE COOLING UNIT CASE SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



29. REMOVE COOLING UNIT CASE SUB-ASSEMBLY (w/o Air Conditioning System)


    E246468
  1. Remove the 7 screws.

  1. Disengage the 2 claws and remove the cooling unit case sub-assembly.



30. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250759
  1. Remove the No. 1 cooler evaporator sub-assembly with evaporator pipe as a unit.



31. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



32. REMOVE COVER PLATE (w/o Air Conditioning System)
  1. Remove the cover plate.



33. REMOVE NO. 1 COOLER THERMISTOR (for Automatic Air Conditioning System)


    E250760
  1. Remove the No. 1 cooler thermistor.



34. REMOVE NO. 1 COOLER THERMISTOR (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



35. REMOVE AIR CONDITIONER TUBE ASSEMBLY (for Automatic Air Conditioning System)


    E250774
  1. Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and air conditioner tube assembly.



36. REMOVE AIR CONDITIONER TUBE ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



37. REMOVE BLOWER MOTOR CONTROL (for Automatic Air Conditioning System)


    E250761
  1. Remove the 2 screws and remove the blower motor control.



38. REMOVE BLOWER RESISTOR (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



39. REMOVE BLOWER RESISTOR (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



40. REMOVE COOLER BLOWER CASE


    E246469
  1. Remove the 4 screws and disengage the 2 claws.

  1. Remove the cooler blower case from the lower heater case.



41. REMOVE COOLER UNIT CASE PACKING (for Automatic Air Conditioning System)


    E250764
  1. Remove the cooler unit case packing.



42. REMOVE COOLER UNIT CASE PACKING (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



43. REMOVE COVER PLATE


    E252254
  1. Remove the cover plate.