Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL COVER PLATE


    E252254
  1. Install the cover plate.



2. INSTALL COOLER UNIT CASE PACKING (for Automatic Air Conditioning System)


    E250764
  1. Install the cooler unit case packing.



3. INSTALL COOLER UNIT CASE PACKING (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



4. INSTALL COOLER BLOWER CASE
  1. Install the cooler blower case from the lower heater case.



    E246469
  1. Engage the 2 claws.

  1. Install the blower case assembly with the 4 screws.



5. INSTALL BLOWER MOTOR CONTROL (for Automatic Air Conditioning System)


    E250761
  1. Install the blower motor control with the 2 screws.



6. INSTALL BLOWER RESISTOR (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



7. INSTALL BLOWER RESISTOR (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



8. INSTALL AIR CONDITIONER TUBE ASSEMBLY (for Automatic Air Conditioning System)


    E250774
  1. Using a 4 mm hexagon wrench, install the air conditioner tube assembly with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



9. INSTALL AIR CONDITIONER TUBE ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



10. INSTALL NO. 1 COOLER THERMISTOR (for Automatic Air Conditioning System)


    E250743E01
  1. Install the No. 1 cooler thermistor as shown in the illustration.
    Part
    Length
    *a
    34.3 mm
    *b
    27.6 mm
    *c
    50 mm
    Text in Illustration 
    *1
    Sensor Part
    *2
    Fixed Part
    *3
    from Tank

    NOTICE:
    1. Be sure to insert the thermistor only once because reinserting it will not allow it to be firmly secured.
    2. When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).
    3. After inserting the thermistor, do not apply excessive force to the wire.
    4. Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".



11. INSTALL NO. 1 COOLER THERMISTOR (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



12. INSTALL COVER PLATE (w/o Air Conditioning System)
  1. Install the cover plate.



13. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250759
  1. Install the No. 1 cooler evaporator sub-assembly with evaporator pipe as a unit.



14. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



15. INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E246468
  1. Engage the 2 claws.

  1. Install the cooling unit case sub-assembly with the 7 screws.



    E250758
  1. Engage the clamp.



16. INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



17. INSTALL COOLING UNIT CASE SUB-ASSEMBLY (w/o Air Conditioning System)


    E246468
  1. Engage the 2 claws.

  1. Install the cooling unit case sub-assembly with the 7 screws.



18. INSTALL HEATER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

NOTICE:
  1. When working, take care not to get dirt or dust in the gear grease.
  2. Do not hold gear sections while wearing cotton work gloves.



    E254919
  1. Turn the pin on the cable side as far as possible in the direction of the arrow, and position it so that it matches the hole in the gear.

    HINT:
    Set the temperature adjustment dial to MAX HOT.



    E254922E01
  1. Hold the protrusion on the drive gear, and rotate the gear until the protrusion is aligned with the cylindrical section of the case.
    Text in Illustration 
    *1
    Drive gear hole
    *2
    Control cable positioning pin

    HINT:
    Temperature adjustment dial: MAX HOT

  1. Push the control cable positioning pin in slowly until it matches the drive gear hole, and install the heater control cable sub-assembly.



  1. Replacing the drive gear.



      E246474E01
    1. When replacing the drive gear, pull the resin portion of the control cable forward slowly and remove it.
      Text in Illustration 
      *1
      Shaft Gear
      *2
      Drive Gear
      *a
      Reference Position
      *b
      Drive gear protrusion
      *c
      Cylindrical section of the case
      *d
      Resin portion of the control cable

      NOTICE:
      Do not pull the drive gear.

    2. Pull the drive gear forward slowly and remove it.

    3. Rotate the shaft gear clockwise slowly until it stops.

      NOTICE:
      Be sure not to turn too forcefully.

    4. Match the shaft gear and the drive gear with their specified positions, and insert the drive gear slowly into the heater case.



19. INSTALL HEATER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



20. INSTALL AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

NOTICE:
  1. When working, take care not to get dirt or dust in the gear grease.
  2. Do not hold gear sections while wearing cotton work gloves.



    E254920
  1. Turn the pin on the cable side as far as possible in the direction of the arrow, and position it so that it matches the hole in the gear.

    HINT:
    Set the blower dial to FACE.



    E254921E01
  1. Hold the protrusion on the drive gear, and rotate the gear clockwise until it stops.
    Text in Illustration 
    *1
    Drive gear hole
    *2
    Control cable positioning pin

    HINT:
    Temperature control position: VENT

  1. Push the control cable positioning pin in slowly until it matches the drive gear hole, and install the air inlet damper control cable sub-assembly.



  1. Replacing the drive gear.



      E246472E01
    1. When replacing the drive gear, pull the resin portion of the control cable forward slowly and remove it.
      Text in Illustration 
      *1
      Mode Main Link
      *2
      Drive Gear
      *a
      Reference Position
      *b
      Drive gear protrusion
      *c
      Resin portion of the control cable

      NOTICE:
      Do not pull the drive gear.

    2. Pull the drive gear forward slowly and remove it.

    3. Match the mode main link and the drive gear with their specified positions, and insert the drive gear slowly into the heater case.



21. INSTALL AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



22. INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250768
  1. Align the link pin and the main link groove, and install the No. 3 air conditioner radiator damper servo sub-assembly with the three screws.



23. INSTALL NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250767
  1. Install the No. 4 air conditioning radiator damper servo sub-assembly with the 2 screws.



24. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    E246467
  1. Install the No. 2 air duct sub-assembly with the 3 screws.



25. INSTALL BLOWER MOTOR WITH FAN SUB-ASSEMBLY


    E250755
  1. Install the blower motor with fan sub-assembly with the 3 screws.



26. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    E250754
  1. Install the No. 1 air duct sub-assembly with the 2 screws.



27. INSTALL NO. 1 COOLER UNIT DRAIN HOSE


    E256351E01
  1. Install the No. 1 cooler unit drain hose as shown in the illustration.
    Text in Illustration 
    *1
    Case
    *2
    Hose
    *a
    Rib
    *b
    Notched section

    HINT:
    Align the notched section of the hose with the rib on the case.



28. INSTALL COVER


    E250752
  1. Engage the 2 claws.

  1. Install the cover with the 3 screws.



29. INSTALL COOLER EXPANSION VALVE (for Automatic Air Conditioning System)


    E250766
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

    Compressor oil:
    for HFC-134a (R134a):
    ND-OIL 8 or equivalent
    for HFO-1234yf (R1234yf):
    ND-OIL 12 or equivalent



    E250765
  1. Using a 4 mm hexagon wrench, install the cooler expansion valve with packing with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



    E250751
  1. Install the new gasket.



30. INSTALL COOLER EXPANSION VALVE (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



31. INSTALL COOLING UNIT CASE


    E252240
  1. Engage the 4 claws.

  1. Install the cooling unit case with the 2 screws.



32. INSTALL CLEAN AIR FILTER


    E250788
  1. Install the clean air filter as shown in the illustration.



33. INSTALL AIR FILTER CASE


    E250748
  1. Engage the 2 claws to install the air filter case.



34. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E250783
  1. Install the heater radiator unit sub-assembly as shown in the illustration.



    E250746
  1. Install the clamp with the screw.



35. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



36. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



37. INSTALL HEATER COVER (for Automatic Air Conditioning System)


    E250745
  1. Install the heater cover with the 3 screws.



38. INSTALL HEATER COVER (for Manual Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



39. INSTALL HEATER COVER (w/o Air Conditioning System)

HINT:
Use the same procedure as for the automatic air conditioning system.



40. INSTALL NO. 5 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E246476E01
  1. Turn the air mix shaft slowly in the direction of the arrow until it stops.
    Text in Illustration 
    *1
    Air Mix Shaft
    *2
    Drive Gear
    *a
    Reference Position

    NOTICE:
    Be sure not to turn the air mix shaft too strongly.

  1. Turn the mix shaft so that section A of the air mix shaft matches the reference position of the case.

  1. Match the air mix damper server gear B section and the shaft gear A section.

  1. Install the No. 5 air conditioning radiator damper servo sub-assembly with the 2 screws.



41. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    E246477E01
  1. Turn the air mix shaft slowly in the direction of the arrow until it stops.
    Text in Illustration 
    *1
    Air Mix Shaft
    *2
    Drive Gear
    *a
    Reference Position

    NOTICE:
    Be sure not to turn the air mix shaft too strongly.

  1. Turn the mix shaft so that section A of the air mix shaft matches the reference position of the case.

  1. Match the air mix damper server gear B section and the shaft gear A section.

  1. Install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.



42. INSTALL ASPIRATOR PIPE (for Automatic Air Conditioning System)


    E250773
  1. Install the aspirator pipe.



43. INSTALL ASPIRATOR (for Automatic Air Conditioning System)


    E250772E01
  1. Engage the 2 claws and align the section A with the case side pin, and then install the aspirator and aspirator pipe as one unit.