ROOF HEADLINING > INSTALLATION |
| 1. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Put the roof headlining assembly into the vehicle through the front passenger side door.
Engage the clip at the front of the roof headlining, and install the roof headlining assembly.
Connect the antenna cord sub-assembly connectors.
Install the 3 clips at the rear of the roof headlining.
Engage the 2 clamps and connect the connector from the front pillar LH.
Engage the 3 clamps and connect the connector from the front pillar RH.
| 2. INSTALL VISOR HOLDER |
Engage the 2 claws install the 2 visor holders.
| 3. INSTALL VISOR ASSEMBLY LH |
Connect the connector (w/ Illumination).
Install the visor assembly LH with the 2 screws.
| 4. INSTALL VISOR ASSEMBLY RH |
| 5. INSTALL MAP LIGHT ASSEMBLY |
Connect each connector.
Engage the 2 guides.
Engage the 2 claws and install the map light assembly.
| 6. INSTALL CENTER PILLAR GARNISH LH |
Engage the 2 guides and clip.
Install the center pillar garnish LH with the 2 bolts and clip.
| 7. INSTALL CENTER PILLAR GARNISH RH |
| 8. INSTALL REAR QUARTER TRIM FRONT GARNISH LH |
Engage the claw and clip.
Install the rear quarter trim front garnish LH with the 2 bolts.
| 9. INSTALL REAR QUARTER TRIM FRONT GARNISH RH |
| 10. INSTALL REAR WINDOW SIDE GARNISH LH |
Engage the guide and 2 clips.
Install the rear window side garnish LH with the bolt.
| 11. INSTALL REAR WINDOW SIDE GARNISH RH |
| 12. INSTALL QUARTER TRIM LID SUB-ASSEMBLY LH |
Install the 2 lid cover clips from the quarter trim lid sub-assembly LH.
![]() |
Engage the 2 guides and 6 claws and install the quarter trim lid sub-assembly LH.
| *1 | Lid Cover Clip |
| 13. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH |
| 14. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH |
Engage the 8 clips install the quarter trim panel assembly LH.
Install the clip.
| 15. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH |
| 16. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH |
Fold down the rear seatback assembly.
Engage the 2 clips install the luggage compartment inner trim cover LH.
| 17. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH |
| 18. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH |
Engage the hook and install the separate type rear seat cushion assembly LH.
Install the bolt.
| 19. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH |
| 20. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH |
Install the floor anchor of the front seat outer belt assembly with the bolt.
Check if the ELR locks.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
Install the floor anchor cover.
| 21. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH |
| 22. INSTALL COWL SIDE TRIM BOARD LH |
Engage the 2 clips install the cowl side trim board LH.
Install the clip.
| 23. INSTALL COWL SIDE TRIM BOARD RH |
| 24. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *a | Alignment Mark |
| 25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 26. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 6 claws install the front door scuff plate LH.
| 27. INSTALL FRONT DOOR SCUFF PLATE RH |
| 28. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover (w/curtain shield airbag).
Make sure that the front pillar garnish clip is not damaged.
![]() |
Hook the tip of the front pillar garnish clip on the front pillar garnish LH as shown in the illustration.
| *1 | Front Pillar Garnish Clip |
Turn the front pillar garnish LH in the direction of the arrow.
![]() |
Insert the 2 guides in the direction of the arrow (1).
Engage the 2 clips and the front pillar garnish clip in the direction of the arrow, and install the front pillar garnish LH.
| *1 | Front Pillar Garnish Clip |
| 29. INSTALL FRONT PILLAR GARNISH RH |
| 30. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
| 31. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
Connect connector.
Engage the 6 claws to install the No. 2 instrument panel speaker panel sub-assembly.
| 32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |