Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
The power window system utilizes a mechanism in which the door glass moves down slightly when the door is opened, and in which the glass moves up when the door closed in order to prevent the door molding from being damaged. When the negative (-) battery terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



3. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B316686E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B316675E01
  1. Using a moulding remover, disengage the 6 claws and remove the No. 2 instrument panel speaker panel sub-assembly.
    Text in Illustration 
    *1
    Moulding Remover

  1. Disconnect the connector.



4. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure described for the No. 2 instrument panel speaker panel sub-assembly.



5. REMOVE FRONT PILLAR GARNISH LH


    B319094E01
  1. Pull the upper part of the front pillar garnish LH in the direction of the arrow (1), and disengage the 2 clips and the front pillar garnish clip.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    The front pillar garnish clip should be remained on the front pillar garnish LH.

  1. Pull the front pillar garnish LH in the direction of the arrow (2) and disengage the 2 guides.



    B319095E01
  1. Turn the front pillar garnish LH in the direction of the arrow.

    NOTICE:
    While turning, be careful not to damage the curtain shield airbag.

  1. Disengage the tip of the front pillar garnish clip and remove the front pillar garnish LH.

    NOTICE:
    1. Do not use any tools to disengage the tip of the front pillar garnish clip.
    2. Be careful not to damage the front pillar garnish clip.

    Text in Illustration 
    *1
    Front Pillar Garnish Clip



    B315206E01
  1. Protect the curtain shield airbag assembly (w/curtain shield airbag).
    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly
    *2
    Adhesive Tape
    *3
    Protective Cover

  1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

    NOTICE:
    Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.



6. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



7. REMOVE FRONT DOOR SCUFF PLATE LH


    B315201
  1. Disengage the 6 claws and remove the front door scuff plate LH.



8. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B315203
  1. Remove the front door opening trim weatherstrip LH.



10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



11. REMOVE COWL SIDE TRIM BOARD LH


    B315202
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board LH.



12. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



13. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH


    B311331E01
  1. Turn back the floor anchor cover.
    Text in Illustration 
    *1
    Floor Anchor Cover

  1. Loosen the bolt and disconnect the floor anchor of the front seat outer belt assembly.



14. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



15. REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH


    B299993
  1. Remove the bolt.

  1. Disengage the hook and remove the separate type rear seat cushion assembly LH.



16. REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



17. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B321716
  1. Fold down the bench type rear seatback assembly.

  1. Disengage the 2 clips and disconnect the luggage compartment inner trim cover LH.



18. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH

HINT:
Use the same procedure described for the LH side.



19. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH


    B315207
  1. Pull up the rear seatback assembly.

  1. Remove the clip.

  1. Disengage the 8 clips and remove the luggage compartment trim cover LH.



20. REMOVE LUGGAGE COMPARTMENT TRIM COVER RH

HINT:
Use the same procedure described for the LH side.



21. REMOVE QUARTER TRIM LID SUB-ASSEMBLY LH


    B315208
  1. Along the arrow in the illustration, disengage the 6 claws.



    B315209
  1. Disengage the 2 clips and 2 guides.

    HINT:
    Make the quarter trim lid sub-assembly LH hang down from the lid cover clip.



    B316678E01
  1. Push the lid cover clip knobs in the direction of the arrow to remove the 2 lid cover clips along with the quarter trim lid sub-assembly LH.
    Text in Illustration 
    *1
    Lid Cover Clip

  1. Remove the 2 lid cover clips from the lid cover LH.

    NOTICE:
    If there is any damage, be sure to replace the lid cover clip with a new one.



22. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



23. REMOVE REAR WINDOW SIDE GARNISH LH


    B315213
  1. Remove the bolt.

  1. Disengage the 2 clips and guide remove the rear window side garnish LH.



24. REMOVE REAR WINDOW SIDE GARNISH RH

HINT:
Use the same procedure described for the LH side.



25. REMOVE REAR QUARTER TRIM FRONT GARNISH LH


    B315215
  1. Remove the 2 bolts.

  1. Disengage the clip and claw remove the rear quarter trim front garnish LH.



26. REMOVE REAR QUARTER TRIM FRONT GARNISH RH

HINT:
Use the same procedure described for the LH side.



27. REMOVE CENTER PILLAR GARNISH LH


    B317118
  1. Remove the 2 bolts and clip.

  1. Disengage the clips and 2 guides to remove the center pillar garnish LH.



28. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



29. REMOVE MAP LIGHT ASSEMBLY


    E247210
  1. Disengage the 2 claws.



    E247211
  1. Disengage the 2 guides and disconnect the map light assembly.



    E247212
  1. Disconnect the connector and remove the map light assembly.



30. REMOVE VISOR ASSEMBLY LH


    B315216
  1. Remove the 2 screws.



    B315217
  1. Disconnect the connector and remove the visor assembly LH (w/ Illumination).



31. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



32. REMOVE VISOR HOLDER


    B315218
  1. Disengage the 2 claws remove the 2 visor holders.



33. REMOVE ROOF HEADLINING ASSEMBLY


    B310223
  1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.



    B310224
  1. Disengage the 2 clamps and disconnect the connector from the front pillar LH.



    B310225
  1. Remove the 3 clips at the rear of the roof headlining.



    B310226
  1. Disconnect the antenna cord sub-assembly connector.



    B310227
  1. Disengage the clip at the front of the roof headlining, and remove the roof headlining assembly.



    B315250
  1. Remove the roof headlining assembly from the vehicle through the front passenger side door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.