Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311498E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  2. Disconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.

  3. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-1 (BECU) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    None - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    None - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-11 (GND) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-32 (BMPX) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    D5-22 (KSW) - Body ground
    BR - Body ground
    Unlock warning switch input
    No key in ignition key cylinder (off)
    Below 1 V
    Key inserted ignition key cylinder (on)
    11 to 14 V
    D6-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    A73-4 (GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω

  4. Reconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.

  5. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.

  6. Measure the voltage and resistance, check for pulse according to the valve(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-28 - Body ground
    Y - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 V
    Driver side door closed
    11 to 14 V
    3B-13 - Body ground
    L - Body ground
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 V
    Passenger side door closed
    11 to 14 V
    3D-26 - Body ground
    SB - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door open
    Below 1 V
    Luggage compartment door closed
    11 to 14 V
    3B-2 - Body ground
    Y - Body ground
    Door lock motor lock drive output (for driver side)
    Door control switch not pushed
    Below 1 V
    Lock side of door control switch pushed
    11 to 14 V
    3B-3 - Body ground
    L - Body ground
    Door lock motor lock drive output (for passenger side)
    Door control switch not pushed
    Below 1 V
    Lock side of door control switch pushed
    11 to 14 V
    3B-1 - Body ground*1, *2
    R-G - Body ground
    Door lock motor unlock drive output (for driver side)
    Door control switch not pushed
    Below 1 V
    Unlock side of door control switch pushed
    11 to 14 V
    3B-4 - Body ground
    L-W - Body ground
    Door lock motor unlock drive output (for passenger side)
    Door control switch not pushed
    Below 1 V
    Unlock side of door control switch pushed
    11 to 14 V
    A73-1 (BZR) - Body ground*3
    V - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    Wireless door lock buzzer on
    Pulse generation
    D6-6 (PRG) - Body ground
    R - Body ground
    Signal output to door control receiver
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    D6-7 (RDA) - Body ground
    V - Body ground
    Signal input from door control receiver
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation

    1. *1: w/o Passenger Side Door Control Switch
    2. *2: w/o Double Locking System
    3. *3: w/ Wireless Door Lock Buzzer Answer-back Function


CHECK DOOR CONTROL RECEIVER

B280754E09

  1. Disconnect the H27 door control receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H27-5 (+B) - Body ground
    Y - Body ground
    Battery power supply
    Always
    11 to 14 V
    H27-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the H27 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H27-3 (PRG) - Body ground
    P - Body ground
    Signal input from main body ECU (network gateway ECU)
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    H27-2 (RDA) - Body ground
    R - Body ground
    Signal output to main body ECU (network gateway ECU)
    Ignition switch off, all doors closed and door control transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter switch pressed
    Pulse generation