Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C238830E01


Text in Illustration 
*a
Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
-
-

Terminal No. (Symbol)
Terminal Description
1 (+BM)
ABS motor relay power supply
2 (SPD)
Speed signal output
3
- (Not used)
4 (FR-)
Front wheel speed RH (-) signal input
5
- (Not used)
6
- (Not used)
7
- (Not used)
8 (FL-)
Front wheel speed LH (-) signal input
9 (CSW2)
TRACK switch input
10
- (Not used)
11
- (Not used)
12 (CSW1)
VSC OFF switch input
13 (GND2)
Pump motor ground
14 (CANL)
CAN communication line L
15
- (Not used)
16 (FR+)
Front wheel speed RH (+) signal input
17 (RR+)
Rear wheel speed RH (+) signal input
18 (RL-)
Rear wheel speed LH (-) signal input
19 (FL+)
Front wheel speed LH (+) signal input
20
- (Not used)
21
- (Not used)
22
- (Not used)
23
- (Not used)
24
- (Not used)
25 (+BS)
ABS solenoid relay power supply
26 (CANH)
CAN communication line H
27
- (Not used)
28 (IG1)
IG1 power source input
29 (RR-)
Rear wheel speed RH (-) signal input
30 (STP)
Stop light switch input
31 (RL+)
Rear wheel speed LH (+) signal input
32
- (Not used)
33
- (Not used)
34
- (Not used)
35
- (Not used)
36
- (Not used)
37
- (Not used)
38 (GND1)
Skid control ECU ground

TERMINAL INSPECTION


  1. Disconnect the connector and measure the voltage and resistance on the wire harness side.


    C238831E03


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))
    -
    -

    HINT:
    The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) because the connector is watertight.


    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A5-1 (+BM) - Body ground
    W - Body ground
    ABS motor relay power supply
    Always
    11 to 14 V
    A5-9 (CSW2) - Body ground
    P - Body ground
    TRACK switch input
    TRACK switch held ON → OFF (Not pressed)
    Below 1 Ω → 10 kΩ or higher
    A5-12 (CSW1) - Body ground
    O - Body ground
    VSC OFF switch input
    VSC OFF switch held ON → OFF (Not pressed)
    Below 1 Ω → 10 kΩ or higher
    A5-13 (GND2) - Body ground
    B - Body ground
    Pump motor ground
    Always
    Below 1 Ω
    A5-25 (+BS) - Body ground
    G - Body ground
    ABS solenoid relay power supply
    Always
    11 to 14 V
    A5-28 (IG1) - Body ground
    G-R - Body ground
    IG1 power source input
    Ignition switch ON
    11 to 14 V
    A5-30 (STP) - Body ground
    R - Body ground
    Stop light switch input
    Stop light switch ON → OFF (Brake pedal depressed → released)
    11 to 14 V* → Below 1.5 V
    A5-38 (GND1) - Body ground
    B - Body ground
    Skid control ECU ground
    Always
    Below 1 Ω

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.