Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR

LUGGAGE COMPARTMENT DOOR > DISASSEMBLY

for Preparation Click here



1. REMOVE LUGGAGE COMPARTMENT DOOR COVER (w/ Entry and Start System)


    B310905
  1. Remove the 7 clips and luggage compartment door cover.



2. REMOVE REAR SPOILER (for Sport Package)
(Click here)


3. REMOVE REAR SPOILER (except Sport Package)
(Click here)


4. REMOVE LUGGAGE COMPARTMENT DOOR CUSHION


    B310906
  1. Disengage the 2 claws and remove the 2 luggage compartment door cushions.



5. REMOVE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B311555
  1. Remove the 2 nuts and the luggage compartment door lock cylinder assembly.



    B311556E01
  1. Disconnect the luggage closer cable assembly.
    Text in Illustration 
    *1
    Luggage Closer Cable Assembly



6. REMOVE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER PACKING (w/ Lock Cylinder)


    B311557E01
  1. Remove the luggage compartment door lock cylinder packing.

    NOTICE:
    Do not reuse the removed packing. Be sure to install a new luggage compartment door lock cylinder packing to prevent water ingress.

    Text in Illustration 
    *1
    Luggage Compartment Door Lock Cylinder Packing



7. REMOVE LUGGAGE DOOR CLOSER ASSEMBLY


    B311552E01
  1. Disconnect the connector.

  1. Disengage the claw and open the cover.
    Text in Illustration 
    *1
    Cover



    B311553E01
  1. Disconnect the luggage closer cable assembly.
    Text in Illustration 
    *1
    Luggage Closer Cable Assembly



    B311554
  1. Remove the 2 bolts and the luggage door closer assembly.



8. REMOVE LUGGAGE CLOSER CABLE ASSEMBLY (w/ Lock Cylinder)


    B311558
  1. Disengage the clamp and remove the luggage closer cable assembly.



9. REMOVE LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    B313074
  1. Disconnect the back door opener switch assembly connector.

  1. Remove the back door opener switch assembly grommet.



    B313075
  1. Disconnect the 2 license plate light connectors.



    B313076
  1. Remove the 3 nuts.

  1. Disengage the clip and remove the luggage compartment door outside garnish sub-assembly.



10. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY


    B310915
  1. Disengage the 2 claws and remove the back door opener switch assembly.



11. REMOVE RADIATOR GRILLE EMBLEM (for Rear Side)


    B314948E01
  1. Apply protective tape to the luggage compartment door panel in the area around the radiator grille emblem.
    Text in Illustration 
    *1
    Wooden Block
    *2
    Piano Wire
    *3
    Protective Tape
    *4
    Location Pin

  1. Using an infrared light, heat the luggage compartment door panel and the radiator grille emblem.

    Heating Temperature:
    Item
    Temperature
    Luggage Compartment Door Panel
    40 to 60°C (104 to 140°F)
    Radiator Grille Emblem
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself with the hot luggage compartment door panel and radiator grille emblem or with the infrared light.

    NOTICE:
    Do not heat the luggage compartment door panel and radiator grille emblem excessively.

  1. Insert piano wire between the luggage compartment door panel and radiator grille emblem.

    HINT:
    Be careful of the location pin positions.

  1. Tie objects that can serve as handles (for example, wooden blocks) to the piano wire ends.

  1. Pull the piano wire and scrape off the double-sided tape that holds the radiator grille emblem to the luggage compartment door panel.

    NOTICE:
    Be careful not to damage the luggage compartment door panel.

  1. Remove the radiator grille emblem.



12. REMOVE LICENSE PLATE LIGHT ASSEMBLY


    B312240
  1. Disconnect the connector.

  1. Disengage the 2 claws to remove the license plate light assembly.

    HINT:
    Use the same procedure as for the other side.



13. REMOVE LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH CAP (w/o Lock Cylinder)


    B405801
  1. Disengage the 2 claws and remove the luggage compartment door outside garnish cap.



14. REMOVE LUGGAGE COMPARTMENT DOOR SUPPORT ASSEMBLY (for LH Side)

NOTICE:
  1. Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.
  2. Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
  3. In order to prevent the piston rod from deforming, do not apply any horizontal load to the door support.



    B310908E01
  1. Using a screwdriver, remove the 2 stop rings along the groove.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Stop Ring

    HINT:
    Tape the screwdriver tip before use.

  1. Release the ball joint and remove the luggage compartment door support.

    NOTICE:
    Remove the luggage compartment door support while supporting the luggage compartment door by hand.



15. REMOVE LUGGAGE COMPARTMENT DOOR SUPPORT ASSEMBLY (for RH Side)

HINT:
Use the same procedure as for the LH side.



16. REMOVE PROTECTOR SEAL (w/ Rear Spoiler (except Sport Package))

HINT:
Perform this procedure only when removal of the protector seal is necessary.