Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING

FRONT DOOR BELT MOULDING > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
The power window system utilizes a mechanism in which the door glass moves down slightly when the door is opened, and in which the glass moves up when the door closed in order to prevent the door molding from being damaged. When the negative (-) battery terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



2. REMOVE DOOR ARMREST COVER


    B313118E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 7 claws.

  1. Disengage the guides and remove the door armrest cover.
    Text in Illustration 
    *1
    Protective Tape



3. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313119E01
  1. Using a screwdriver with its tip wrapped in protective tape, open the cap.
    Text in Illustration 
    *1
    Protective Tape



    B313120
  1. Using a clip remover, disengage the clip.

  1. Remove the 3 screws.



    B313121
  1. Using a moulding remover, disengage the 10 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Disconnect each connector.

  1. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door glass weatherstrip inner.



    B313122E01
  1. Disconnect the front door lock remote control cable and the front door inside locking cable.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable
    *2
    Front Door Lock Remote Control Cable



4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B314154
  1. Remove the 4 screws and power window regulator master switch assembly with the front door armrest base panel.



5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B314155
  1. Remove the 4 screws and power window regulator switch assembly with front door armrest base panel.



6. REMOVE FRONT DOOR SERVICE HOLE COVER


    B314956
  1. Disconnect the outer rear view mirror sub-assembly connector.



    B314160
  1. Disconnect the front door lock assembly connector.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



7. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


B314161
  1. Provisionally install the power window regulator master switch (for driver side).

  1. Provisionally install the power window regulator switch (for passenger side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly until the 2 nuts can be seen through the service holes.

  1. Disconnect the power window regulator master switch connector (for driver side).

  1. Disconnect the power window regulator switch connector (for passenger side).

  1. Disconnect the cable from the negative (-) battery terminal.



    B314162
  1. Remove the 3 nuts.

  1. Shift the front door rear lower frame sub-assembly to the lower side of the door frame.



    B386125E01
  1. Install SST as shown in the illustration.
    Text in Illustration 
    *1
    Door Glass Inner Stabilizer Bolt
    *2
    Nut A
    *3
    Nut B
    *4
    Front Door Glass Sub-assembly
    *5
    Front Door Window Regulator Sub-assembly
    *6
    Bolt
    *a
    SST Number

    SST
    09801-18010  

    HINT:
    The SST number on SST must be visible.

  1. Secure the bolt using SST, and then remove nut A.

  1. Remove nut B from the front door glass sub-assembly.

  1. Loosen the door glass inner stabilizer bolt.

    NOTICE:
    After the 2 nuts are removed, do not allow the door glass to fall.



    B314795
  1. While holding the front door glass sub-assembly up, slide the front door rear lower frame sub-assembly downward, and pull the front door glass sub-assembly out from the front door rear lower frame sub-assembly.

    NOTICE:
    1. Do not allow the door glass to fall.
    2. Do not damage the door glass.

  1. Partially remove the rear end of the front door weatherstrip until the front door glass sub-assembly can be removed.



    B314796
  1. Remove the front door glass sub-assembly from the position indicated in the illustration.

    NOTICE:
    Do not damage the front door weatherstrip.

    HINT:
    The front glass sub-assembly can only be removed from the position indicated in the illustration.



8. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
  1. Remove the front door rear lower frame sub-assembly from the front door frame.



9. REMOVE FRONT DOOR SUSH


    B314797
  1. Remove the 3 nuts.



    B314798E01
  1. Rotate the front door sush as indicated by the arrows in the order shown in the illustration, and remove the front door sush.

    NOTICE:
    1. Since the front door sush attachment bolts interfere, be sure to follow the procedure shown in the illustration.
    2. Do not allow the front door sush to fall.
    3. Do not damage the front door sush.



10. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B314914E01
  1. Remove the screw.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, disengage the claw and remove the front door glass outer weatherstrip assembly.

    HINT:
    Tape the screwdriver tip before use.