HEADLIGHT ASSEMBLY (for Halogen Headlight) > INSTALLATION |
| 1. INSTALL HEADLIGHT ASSEMBLY |
Engage the clamp.
Install the headlight assembly with the bolt.
Install the clip.
Connect each connector.
| 2. INSTALL FRONT BUMPER SIDE SUPPORT LH |
Install the front bumper side support LH with the 3 bolts B.
Install the bolt A.
Engage the 2 clamps to connect the wire harness.
| 3. INSTALL FRONT BUMPER COVER |
| 4. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT |
Prepare the vehicle:
![]() |
| 5. PREPARE FOR HEADLIGHT AIMING |
![]() |
Prepare the vehicle (except China):
| *a | 25 or 3 m (82 or 9.84 ft.) |
| *b | 90° |
![]() |
Prepare the vehicle (for China):
| *a | 10 or 3 m (32.8 or 9.84 ft.) |
| *b | 90° |
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration (except China).

| *A | Aligning distance 25 m (82 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | V Line |
| *e | 90° | *f | 25 m (82 ft.) |
| *g | 3 m (9.84 ft.) | - | - |
Set the screen as shown in the illustration (for China).

| *A | Aligning distance 10 m (32.8 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | V Line |
| *e | 90° | *f | 10 m (32.8 ft.) |
| *g | 3 m (9.84 ft.) | - | - |
![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).
| *a | V LH Line |
| *b | V Line |
| *c | V RH Line |
| *d | H Line |
| *e | Ground |
| 6. INSPECT HEADLIGHT AIMING |
Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.
Start the engine.
Turn on the headlights and check if the cutoff line for each low beam matches the preferred cutoff line in the illustration (except China).

| *A | Aligning distance 25 m (82 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V LH Line | *b | V RH Line |
| *c | H Line | *d | Preferred Cutoff Line |
| *e | Point A | - | - |
Turn on the headlights and check if the cutoff line for each low beam matches the preferred cutoff line in the illustration (for China).

| *A | Aligning distance 10 m (32.8 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V LH Line | *b | V RH Line |
| *c | H Line | *d | Point A |
Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration (for China).

| *A | Aligning distance 10 m (32.8 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V LH Line | *b | V RH Line |
| *c | H Line | *d | Center of Intensity |
| 7. ADJUST HEADLIGHT AIMING |
Remove any covers necessary to access the headlight adjusters.
![]() |
Adjust the aim vertically:
Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.
| *1 | Aiming Screw A |
![]() |
Turn aiming screw B the same number of turns and in the same direction as aiming screw A.
| *1 | Aiming Screw B |