Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311498E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  2. Disconnect the D6 and A73 main body ECU (network gateway ECU) connectors.

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-1 (BECU) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-32 (BMPX) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    None - Body ground
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    None - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    D6-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    A73-4 (GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω

  4. Reconnect the D6 and A73 main body ECU (network gateway ECU) connectors.

  5. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.

  6. Measure the voltage, check for pulse according to the valve(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-28 - Body ground
    V - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 V
    Driver side door closed
    11 to 14 V
    3B-13 - Body ground
    GR - Body ground
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 V
    Passenger side door closed
    11 to 14 V
    3D-26 - Body ground
    SB - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door open
    Below 1 V
    Luggage compartment door closed
    11 to 14 V
    3B-2 - Body ground
    Y - Body ground
    Door lock motor lock drive output
    Door control switch not pushed
    Below 1 V
    Lock side of door control switch pushed
    11 to 14 V
    3B-3 - Body ground
    L - Body ground
    Door lock motor lock drive output
    Door control switch not pushed
    Below 1 V
    Lock side of door control switch pushed
    11 to 14 V
    3B-6 - Body ground
    G - Body ground
    Door lock motor lock drive output (for luggage compartment door)
    Luggage open switch of electrical key transmitter sub-assembly not pressed
    Below 1 V
    Luggage open switch of electrical key transmitter sub-assembly pressed
    11 to 14 V
    3B-1 - Body ground*1, *2
    R-G - Body ground
    Door lock motor unlock drive output
    Door control switch not pushed
    Below 1 V
    Unlock side of door control switch pushed
    11 to 14 V
    3B-4 - Body ground
    L-W - Body ground
    Door lock motor unlock drive output
    Door control switch not pushed
    Below 1 V
    Unlock side of door control switch pushed
    11 to 14 V
    A73-1 (BZR) - Body ground
    V - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    Wireless door lock buzzer on
    Pulse generation
    D5-22 (ACC) - Body ground
    W - Body ground
    ACC power supply
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    11 to 14 V
    D6-11 (LSFD) - Body ground
    W - Body ground
    Driver side door unlock detection switch input
    Driver side door unlocked
    Below 1 V
    Engine switch off, all doors closed and driver side door locked
    Pulse generation
    D6-12 (LSFP) - Body ground
    SB - Body ground
    Passenger side door unlock detection switch input
    Passenger side door unlocked
    Below 1 V
    Engine switch off, all doors closed and passenger side door locked
    Pulse generation

    1. *1: w/o Passenger Side Door Control Switch
    2. *2: w/o Double Locking System


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E44

  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D48-2 (+B) - D48-11 (GND)
    R - B
    +B power supply
    Always
    11 to 14 V
    D48-11 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the D48 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D41-5 (IG2) - D48-11 (GND)
    Y - B
    IG power supply
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    D40-5 (RCO) - D48-11 (GND)
    LG - B
    Entry door control receiver power source
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V
    D40-17 (RDA) - D48-11 (GND)
    P - B
    Entry door control receiver data input signal
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    11 to 14 V pulse generation at regular intervals
    D40-19 (RSSI) - D48-11 (GND)
    R - B
    Entry door control receiver electric wave existence signal
    All door locked, all doors closed and electrical key switch on
    11 to 14 V → Below 2 V


CHECK DOOR CONTROL RECEIVER
B109870
  1. Disconnect the H26 door control receiver connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H26-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the H26 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H26-2 (RSSI) - H26-1 (GND)
    BR - B
    Entry door control receiver electric wave existence signal
    All door locked, all doors closed and electrical key switch on
    11 to 14 V → Below 2 V
    H26-5 (DATA) - H26-1 (GND)
    G - B
    Entry door control receiver data input signal
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    11 to 14 V pulse generation at regular intervals
    H26-4 (+5) - H26-1 (GND)
    Y - B
    Entry door control receiver power source
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V