Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM

STEERING LOCK SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Body / (desired system) / Data List.

  6. According to the display on the GTS, read the Data List.



  7. Using the GTS, confirm the Data List items to help determine the cause of the problem.

    NOTICE:
    1. The steering lock actuator assembly (steering lock ECU) communicates with the GTS through the certification ECU (smart key ECU assembly) which uses CAN communication. If the CAN communication system or certification ECU (smart key ECU assembly) is malfunctioning, Data List items may not be normal.
    2. When using the GTS with the engine switch off (lock), perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.


    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal*1
    Shift position (P) signal / OFF or ON
    OFF: Shift lever is not in P
    ON: Shift lever is in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The engine cannot be started when this item is "OFF".
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly / OFF or ON
    OFF: Steering locked (Engine switch off door opened)
    ON: Steering unlocked (Engine switch on (ACC))
    This item can be used to determine the cause of problems when the steering does not lock or unlock.

    HINT:
    1. The steering is considered locked when the lock sensor is ON and the unlock sensor is OFF.
    2. The steering is considered unlocked when the lock sensor is OFF and the unlock sensor is ON.

    Str Lock/Unlock Wait T-Out
    Steering lock or unlock malfunction / No or Yes
    No: Steering locks/unlocks normally within specified time
    Yes: Steering lock/unlock timed out (Lock bar stuck, etc.)
    The engine cannot be started when this item is "Yes".
    1. *1: for Automatic Transmission

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    State of certification ECU (smart key ECU assembly) IG power supply input / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    This item displays "OFF" when the engine switch is on (ACC).
    Immobiliser*1
    State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset
    Unset: Engine immobiliser unset (engine switch on (ACC) or on (IG))
    Set: Engine immobiliser set (engine switch off)
    1. When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is part of the problem.
    2. The engine cannot be started when this item displays "Set"
    Immobiliser*2
    State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset
    Unset: Engine immobiliser unset (engine switch on (ACC) or on (IG))
    Set: Engine immobiliser set (engine switch off)
    1. When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) is part of the problem.
    2. The engine cannot be started when this item displays "Set"
    Steering Lock Sleep Cond
    steering lock actuator assembly (steering lock ECU) sleep condition / No or Yes
    -
    -
    Steering Lock Start Cond
    Transmission state of steering lock actuator assembly (steering lock ECU) wake up signal / No or Yes
    No: Wake up signal not transmitted
    Yes: Wake up signal transmitted
    -
    Engine Start Condition
    State of engine start permission signal determined by steering lock actuator assembly (steering lock ECU) and sent to certification ECU (smart key ECU assembly) / OK or NG
    OK: Engine start permitted
    NG: Engine start prohibited
    1. When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock actuator assembly (steering lock ECU) and has permitted fuel injection and engine combustion.
    2. The engine cannot be started when this item displays "NG".
    Sensor Value
    Malfunction history of position sensor in steering lock actuator / OK or NG (Past)
    OK: No record of lock/unlock sensor malfunction in steering lock actuator
    NG(Past): Record of lock/unlock sensor in steering lock actuator turning ON at same time exists
    When this item displays "NG", the sensor inside the steering lock actuator may be malfunctioning, or there may be a mechanical malfunction.
    Power Supply Short
    Record of malfunction of signal sent to steering lock actuator assembly (motor) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG (Past)
    OK: No record of malfunction (short circuit)
    NG (Past): Record of malfunction (short circuit) exists
    This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock actuator assembly (motor).
    Motor Driver Short
    Record of malfunction of motor activation circuit in steering lock actuator assembly (short circuit) (DTC B2781 stored) / OK or NG (Past)
    OK: No record of malfunction (short circuit)
    NG (Past): Record of malfunction (short circuit) exists
    This item records malfunctions in the motor activation circuit inside the steering lock actuator assembly (short circuit).
    Lock/Unlock Receive
    Reception state of steering lock or unlock request signal from certification ECU (smart key ECU assembly) / No or Yes
    No: No record of receiving lock or unlock request signal
    Yes: Record of receiving lock or unlock request signal exists
    -
    Lock Bar Stuck Error
    Record of lock bar not properly unlocking after being commanded to unlock for certain amount of time / OK or NG (Past)
    OK: No record of stuck lock bar
    NG (Past): Record of stuck lock bar exists
    -
    Push Start Error
    Record of malfunction of push-start function due to steering lock actuator / OK or NG (Past)
    OK: No record of push-start function malfunction
    NG (Past): Record push-start function malfunction exists
    -
    Engine Start Request
    Reception state of engine start permission signal determined by steering lock actuator assembly and sent to certification ECU (smart key ECU assembly) / OK or NG
    OK: Receiving signal
    NG: Not receiving signal
    1. When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock actuator assembly (steering lock ECU) and has permitted fuel injection and engine combustion.
    2. The engine cannot be started when this item displays "NG".
    S Code Check*1
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is not registered or the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).
    L Code Check*1
    Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is not registered or the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).
    L Code Check*2
    Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is not registered or the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).
    Unlock Request Receive*1
    Reception state of steering unlock command signal determined by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG"

    OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
    NG: Except above
    1. If the unlock signal has not been received, the engine cannot be started.
    2. If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Unlock Request Receive*2
    Reception state of steering unlock command signal determined by certification ECU (smart key ECU assembly) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG"

    OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
    NG: Except above
    1. If the unlock signal has not been received, the engine cannot be started.
    2. If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Lock Request Receive*1
    Reception state of steering lock command signal determined by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG"

    OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*3
    NG: Except above
    If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Lock Request Receive*2
    Reception state of steering lock command signal determined by certification ECU (smart key ECU assembly) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG"

    OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*3
    NG: Except above
    If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    S Code Check(Past)*1
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past) / OK or NG (Past)
    OK: Verification result normal
    NG: Verification result abnormal (Past)
    -
    L Code Check(Past)*1
    Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly (Past) / OK or NG (Past)
    OK: Verification result normal
    NG: Verification result abnormal (Past)
    -
    L Code Check(Past)*2
    Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly (Past) / OK or NG (Past)
    OK: Verification result normal
    NG: Verification result abnormal (Past)
    -
    Steering Lock
    State of whether steering lock actuator assembly (steering lock ECU) has determined steering is locked / Unset or Set
    Unset: Steering unlocked
    Set: Steering locked
    If this item displays "Unset", the steering does not lock.
    Steering Unlock
    State of whether steering lock actuator assembly (steering lock ECU) determined steering is unlocked / Unset or Set
    Unset: Steering locked
    Set: Steering unlocked
    If this item displays "Unset", the steering does not unlock (engine cannot be started).
    # Codes
    Number of DTCs / 0 to 255
    -
    -
    1. *1: w/ ID Code Box
    2. *2: w/o ID Code Box
    3. *3: for Automatic Transmission
    Unlock operation conditions for the steering lock:
    1. When the following condition is met, the unlock operation is performed.
      1. The engine switch is on (ACC) or on (IG).
        1. When the engine switch is turned on (ACC) or on (IG), and the key and certification ECU (smart key ECU assembly) are verified, the steering is unlocked.

          HINT:
          1. When any of the following conditions are met, key verification is performed.
            1. The brake pedal (for automatic transmission) or clutch pedal (for manual transmission) is depressed so that the engine can be started.
            2. 30 seconds elapse after opening and closing a door.
            3. The engine switch is pressed.
          2. Key verification occurs when the code emitted from the key and the code stored in the certification ECU (smart key ECU assembly) are compared to check that they match.
          3. Certification ECU (smart key ECU assembly) verification occurs when the S code and L code are verified while the engine is being started or the engine switch is being pushed. The S code is used for certification between the ID code box (immobiliser code ECU) and the certification ECU (smart key ECU assembly). The L code is used for certification between the ID code box (immobiliser code ECU) and the steering lock actuator assembly (steering lock ECU).*1
          4. Certification ECU (smart key ECU assembly) verification occurs when the L code is verified while the engine is being started or the engine switch is being pushed. The L code is used for certification between the certification ECU (smart key ECU assembly) and the steering lock actuator assembly (steering lock ECU).*2
          1. *1: w/ ID Code Box
          2. *2: w/o ID Code Box

    Lock operation conditions for the steering lock:
    1. When the following conditions are met and the certification ECU (smart key ECU assembly) has been verified, the lock operation is performed.
      1. The engine switch is off.
      2. The shift lever is in P (for automatic transmission).
      3. A door is opened or a door lock operation (entry door lock, wireless door lock or key-linked lock operation (w/ key-linked switch)) is performed.

    HINT:
    The following example shows the behavior of various Data List items when the shift lever is in P (for automatic transmission), the brake pedal (for automatic transmission) or clutch pedal (for manual transmission) is not depressed, the vehicle is normal and the power source mode changes.

    C240209E02

    HINT:
    Get into the vehicle while carrying the key. With the engine switch off, the shift lever is in P (for automatic transmission) and all the doors closed, perform the following procedures and check the power source mode.
    *1: Without depressing the brake pedal (for automatic transmission) or clutch pedal (for manual transmission), press the engine switch and check that the power source mode turns on (ACC).
    *2: Without depressing the brake pedal (for automatic transmission) or clutch pedal (for manual transmission), press the engine switch and check that the power source mode turns on (IG).
    *3: Press the engine switch and check that the power source mode turns off.
    *4: Release the brake pedal (for automatic transmission) or clutch pedal (for manual transmission), open the driver side door and check that the steering locks.


    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy switch / ON or OFF
    ON: Driver side door open
    OFF: Driver side door closed
    If this item does not change according to the actual state of the driver side door, there is a malfunction in the door courtesy light switch or related part.