Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM

DTC    B2782    Power Source Control ECU Malfunction

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the SLR+ input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock actuator assembly (steering lock ECU) is determined to be abnormal.

HINT:
The steering lock actuator assembly (steering lock ECU) is not connected to the CAN communication system. However, the steering lock actuator assembly (steering lock ECU) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No.
Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2782
Either condition is met (1-trip detection logic*1):
  1. The steering lock motor activation command circuit has a short circuit.
  2. The steering lock motor activation command circuit has an open circuit.

HINT:
If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.

  1. Steering lock actuator assembly (steering lock ECU)
  2. Certification ECU (Smart key ECU assembly)
  3. Harness or connector
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P*2 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key)
  1. *1: Only output while a malfunction is present and the engine switch is on (IG).
  2. *2: for Automatic Transmission

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started.
Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2782
Entry&Start
  1. Power Supply Short
-

WIRING DIAGRAM


C220331E21


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off (lock), perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.
  2. The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the Service Bulletin.
  4. After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (MOTOR ACTIVATION COMMAND SIGNAL)
  1. Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-1 (SLR+) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.

  1. Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P*.

    1. *: for Automatic Transmission



    C222662E17
  1. Check the signal waveform according to the condition(s) in the table below.
    Standard Frequency 
    Item
    Content
    Tester Connection
    D59-3 (SLR+) - D59-1 (GND)
    Tool Setting
    2 V/DIV., 200 ms./DIV.
    Vehicle Condition
    Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating
    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock Actuator Assembly (Steering Lock ECU))
    *b
    Steering lock motor not operating
    *c
    Steering lock motor operating

HINT:
  1. When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
  2. In order to take measurements when the lock motor is operating, perform either of the following operations:
    1. To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
    2. To lock the steering, turn the engine switch off with the shift lever is in P*, and then open a door.
      1. *: for Automatic Transmission



NG
Go to step 4
OK


2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
  1. Clear the DTCs (Click here).

  1. Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored.

    NOTICE:
    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work (Click here).


NEXT


3.CHECK DTC AND READ VALUE USING GTS (POWER SUPPLY SHORT)
  1. Perform the DTC output confirmation operation.

  1. Check if DTC B2782 is output (Click here).

  1. Use the Data List to check if the steering lock control is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Short
    Record of malfunction of signal sent to steering lock actuator assembly (motor) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG (Past)
    OK: No record of malfunction (short circuit)
    NG (Past): Record of malfunction (short circuit) exists
    This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock actuator assembly (motor).

    Result 
    Result
    Proceed to
    1. B2782 is not output
    2. "OK" is displayed on the GTS.
    A
    1. B2782 is output
    2. "NG (Past)" is displayed on the GTS.
    B



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU))
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.

  1. Check for deformation and corrosion of the connector case and terminals.

    OK:
    There is no deformation or corrosion of the connector case or terminals.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-29 (SLR+) - D59-3 (SLR+)
    Always
    Below 1 Ω
    D59-3 (SLR+) - Body ground
    Always
    10 kΩ or higher
    D41-29 (SLR+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)