Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. If the ignition switch cannot be turned to ON, communication with the GTS can be confirmed by connecting the GTS to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Main Body / Data List.

  5. Enter the following menus: Powertrain / Engine / Data List.

  6. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Number of Registration Key
    Number of registered key/ 0 to 8
    Number of registered key
    -
    IG SW
    Ignition switch ON signal / OFF or ON
    OFF: Ignition switch ACC or off
    ON: Ignition switch ON
    -
    ACC SW
    Ignition switch ACC signal / OFF or ON
    OFF: Ignition switch off
    ON: Ignition switch ACC or ON
    -
    Key Unlock Warning SW
    Unlock warning switch signal / OFF or ON
    OFF: No key in ignition key cylinder
    ON: Key inserted in ignition key cylinder
    -
    Battery Power Supply Control Voltage
    Battery power supply control voltage / 0 to 21.4 V
    11 to 14 V
    -
    Battery Power Supply Back Up Voltage
    Battery power supply backup voltage / 0 to 2.14 V
    11 to 14 V
    -
    IG Power Supply Voltage
    IG power supply voltage / 0 to 21.4 V
    11 to 14 V
    -
    ACC Voltage
    ACC voltage / 0 to 21.4 V
    11 to 14 V
    -
    Immobiliser Light
    Security indicator light status / OFF or ON
    OFF: Security indicator light OFF
    ON: Security indicator light ON
    -
    Immobiliser Power Supply
    Main body ECU (network gateway ECU) engine immobiliser system power supply output status / OFF or ON
    OFF: Power not supplied to engine immobiliser system
    ON: Power supplied to engine immobiliser system
    -

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser Fuel Cut
    Status of immobiliser fuel cut / ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of immobiliser fuel cut history / ON or OFF
    -
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Main Body / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON/OFF
    -