Home › Vehicle Exterior › LIGHTING (EXT) › RELAY

RELAY > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT H-LP RELAY


    A188757E02
  1. Remove the H-LP relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (H-LP Relay)
    If the result is not as specified, replace the H-LP relay.



2. INSPECT DIM RELAY


    A188757E02
  1. Remove the DIM relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (DIM Relay)
    If the result is not as specified, replace the DIM relay.



3. INSPECT RR FOG RELAY


    A188757E02
  1. Remove the RR FOG relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (RR FOG Relay)
    If the result is not as specified, replace the RR FOG relay.



4. INSPECT DRL RELAY (w/o Side Marker Light)


    A188757E02
  1. Remove the DRL relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (DRL Relay)
    If the result is not as specified, replace the DRL relay.



5. INSPECT DRL LH RELAY (w/ Side Marker Light)


    A188757E02
  1. Remove the DRL LH relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (DRL LH Relay)
    If the result is not as specified, replace the DRL LH relay.



6. INSPECT DRL RH RELAY (w/ Side Marker Light)


    A188757E02
  1. Remove the DRL RH relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (DRL RH Relay)
    If the result is not as specified, replace the DRL RH relay.