Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)


    E136492E14
  1. Check the windshield wiper switch assembly.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D58-2 (+1) - D58-3 (+B)
      MIST
      Below 1 Ω
      D58-2 (+1) - D58-4 (+S)
      OFF
      D58-2 (+1) - D58-4 (+S)
      INT
      D58-2 (+1) - D58-3 (+B)
      LO
      D58-1 (+2) - D58-3 (+B)
      HI

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the front washer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D57-1 (WF) - D57-2 (EW)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch.



    E136492E15
  1. Check the intermittent operation.

    1. Turn the ignition switch to on and turn the windshield wiper switch assembly to INT.



    2. Measure the voltage according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      HINT:
      Measure the voltage from the rear of the connectors while they are connected to the windshield wiper switch assembly.

      Specified Condition:
      Voltage changes as shown in the illustration below.



      E136493E09


      Text in Illustration 
      *a
      Voltage between terminals D57-2 (EW) and D58-4 (+S)
      *b
      WIPER OPERATION
      *c
      STOP
      *d
      START
      *e
      0.6 to 2.6 seconds
      *f
      5.7 to 15.7 seconds
      *g
      FAST
      *h
      SLOW



    E136492E18
  1. Check the washer operation.

    1. Turn the ignition switch to on and turn the windshield wiper switch assembly off.



    2. Measure the voltage according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      HINT:
      Measure the voltage from the rear of the connectors while they are connected to the windshield wiper switch assembly.

      Specified Condition:
      Voltage changes as shown in the illustration below.



      E136494E03


      Text in Illustration 
      *1
      Washer Switch
      -
      -
      *a
      Voltage between terminals D57-1 (WF) - D57-2 (EW)
      *b
      Approximately 0.2 seconds
      *c
      Approximately 2.2 seconds
      -
      -
      If the result is not as specified, replace the windshield wiper switch assembly.



2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)


    E136492E19
  1. Check the windshield wiper switch assembly.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D58-3 (+1) - D58-2 (+B)
      MIST
      Below 1 Ω
      D58-3 (+1) - D58-1 (+S)
      OFF
      D58-3 (+1) - D58-1 (+S)
      INT
      D58-3 (+1) - D58-2 (+B)
      LO
      D58-4 (+2) - D58-2 (+B)
      HI

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the front washer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D57-3 (WF) - D57-2 (EW)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch.



    E136492E20
  1. Check the intermittent operation.

    1. Turn the ignition switch to on and turn the windshield wiper switch assembly to INT.



    2. Measure the voltage according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      HINT:
      Measure the voltage from the rear of the connectors while they are connected to the windshield wiper switch assembly.

      Specified Condition:
      Voltage changes as shown in the illustration below.



      E136493E09


      Text in Illustration 
      *a
      Voltage between terminals D57-2 (EW) and D58-1 (+S)
      *b
      WIPER OPERATION
      *c
      STOP
      *d
      START
      *e
      0.6 to 2.6 seconds
      *f
      5.7 to 15.7 seconds
      *g
      FAST
      *h
      SLOW



    E136492E21
  1. Check the washer operation.

    1. Turn the ignition switch to on and turn off the windshield wiper switch assembly.



    2. Measure the voltage according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      HINT:
      Measure the voltage from the rear of the connectors while they are connected to the windshield wiper switch assembly.

      Specified Condition:
      Voltage changes as shown in the illustration below.



      E136494E03


      Text in Illustration 
      *1
      Washer Switch
      -
      -
      *a
      Voltage between terminals D57-3 (WF) - D57-2 (EW)
      *b
      Approximately 0.2 seconds
      *c
      Approximately 2.2 seconds
      -
      -
      If the result is not as specified, replace the windshield wiper switch assembly.