Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. REMOVE FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)


B171377E26
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly LH.



    B171377E27
  1. Check the operation of the door unlock detection switch (w/ Entry and Start System for LHD).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (E) - 8 (LSSR)
      Lock
      10 kΩ or higher
      7 (E) - 8 (LSSR)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly LH.



    B171377E27
  1. Check the operation of the door unlock detection switch (w/ Entry and Start System for RHD).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (E) - 8 (LSSR)
      Lock
      10 kΩ or higher
      7 (E) - 8 (LSSR)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly LH.



2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)


B164418E11
  1. Check the door lock motor operation.

    1. Apply battery voltage to the motor connector and check the operation of the front door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Lock
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlock
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Set
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unset

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly LH)
      *b
      Unlock
      *c
      Lock

      HINT:
      1. Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.
      2. Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      1. If the result is not as specified, replace the front door lock assembly LH.



3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)


B171378E29
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock
      1. If the result is not as specified, replace the front door lock assembly RH.



    B273325E02
  1. Check the detection switch (w/ Entry and Start System for LHD).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly RH.



    B273325E03
  1. Check the detection switch (w/ Entry and Start System for RHD).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly RH.



4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)


B164417E10
  1. Check the operation of the door lock motor and double lock motor.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlock
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Set
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unset

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock

      HINT:
      1. Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.
      2. Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      If the result is not as specified, replace the front door lock assembly RH.



    B273326E02
  1. Check the detection switch (w/ Entry and Start System).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly RH.



    B259282E05
  1. Check the door lock and unlock switch (w/ Key-linked Switch).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 - 8 (E)
      Lock
      Below 1 Ω
      6 - 8 (E)
      5 - 8 (E)
      Off
      10 kΩ or higher
      5 - 8 (E)
      Unlock
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock assembly RH.