Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    U0073    Control Module Communication Bus "A" Off

DTC    U0101    Lost Communication with TCM

DTC    U0122    Lost Communication with Vehicle Dynamics Control Module

DTC    U0155    Lost Communication with Instrument Panel Cluster (IPC) Control Module

DTC    U0402    Invalid Data Received from TCM

DTC    U0416    Invalid Data Received from Vehicle Dynamics Control Module

DTC    U0423    Invalid Data Received from Instrument Panel Cluster Control Module

for Preparation Click here


DESCRIPTION

Refer to CAN communication system for system description (Click here).

DTC No.
DTC Detection Conditions
Trouble Areas
U0073
Bus off state for 0.436 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
U0101
No communication between ECM and TCM for 0.5 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. TCM
U0122
No communication between ECM and skid control ECU for 0.5 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. Brake actuator assembly
U0155
No communication between ECM and combination meter assembly for 0.5 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. Combination meter assembly
U0402
Invalid data received from TCM for 2 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. TCM
U0416
Invalid data received from skid control ECU for 2 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. Brake actuator assembly
U0423
Invalid data received from combination meter assembly for 2 seconds or more
(1 trip detection logic)
  1. Wire harness (CANL and CANH circuits)
  2. ECM
  3. Combination meter assembly

MONITOR DESCRIPTION

The ECM, TCM, skid control ECU and combination meter assembly communicate with each other via the CAN communication line. If there is a problem in this communication, the ECM stores the DTC.

INSPECTION PROCEDURE

Go to CAN communication system for troubleshooting (Click here).

HINT:
  1. When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
  2. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the CAN communication malfunctions, there is no data output from the ECM. In this case, some of the freeze frame data are not correct and not identical with the ECM data, but the ECM data are correct.

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC U0073, U0101, U0122, U0155, U0402, U0416 or U0423 is output
    A
    DTC U0073, U0101, U0122, U0155, U0402, U0416 or U0423 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A

GO TO CAN COMMUNICATION SYSTEM (Click here)