Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2282    Vehicle Speed Signal Malfunction

DTC    B2283    Vehicle Speed Sensor Malfunction

for Preparation Click here


DESCRIPTION

DTC B2282 is stored when a mismatch between the vehicle speed signal from the direct line sent by the brake actuator assembly (skid control ECU) and the vehicle speed signal sent via CAN communication is detected.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2282
Mismatch between the vehicle speed signal from the direct line sent by the brake actuator assembly (skid control ECU) and the vehicle speed signal sent via CAN communication (1-trip detection logic*1).
  1. AM2 No. 2 fuse
  2. Vehicle stability control system
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed that is less than 5 km/h (3 mph) for 20 seconds.
B2283
Either condition is met (vehicle speed sensor malfunction is detected) (1-trip detection logic*1):
  1. Vehicle speed signal malfunction detection 1: Large decrease in speed is detected.
  2. Vehicle speed signal malfunction detection 2: Malfunction detected using engine speed-linked detection.
  1. AM2 No. 2 fuse
  2. Vehicle stability control system
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Run the engine at an engine speed of 2000 rpm or more for 330 seconds.
  1. *1: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
DTC No.
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
B2282
  1. When the signal from the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.
  2. When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power source mode cannot be turned from on (IG) to off.
-
B2283
  1. If the engine switch is pressed while the vehicle is being driven, the engine switch turns off (the engine stops).
  2. When the electrical key transmitter sub-assembly is inside the vehicle, the engine does not start even though an engine start operation is performed.
Steering lock motor operation is prohibited.

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2282
B2283
Power Source Control
  1. Vehicle Speed Signal
  2. Engine Condition
  3. Power Supply Condition
Engine
  1. Engine Speed
ABS/VSC/TRC
  1. Vehicle Speed
-

WIRING DIAGRAM


B286292E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING GTS (VEHICLE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed (Speedometer tester)
    -

    OK:
    The Data List value is approximately the same as the actual vehicle speed.



NG
GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Signal
    Vehicle moving or stationary / Stop or Run
    Run: Vehicle moving at 5 km/h (3 mph) or more
    Stop: Vehicle stopped
    -

    OK:
    Stop (vehicle stopped) or Run (vehicle moving) appears on the screen according to the vehicle speed.



NG
Go to step 3
OK

GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)  

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - COMBINATION METER ASSEMBLY)
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A5 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-27 (SPD) - A5-2 (VSO)
    Always
    Below 1 Ω
    D41-27 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B274541E06


Text in Illustration 
*a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
  1. Reconnect the A5 brake actuator assembly (skid control ECU) connector.

  1. Reconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the vehicle speed input signal waveform from the combination meter at the terminal of the certification ECU (smart key ECU assembly).

    1. Check the signal waveform according to the conditions in the table below.

      Item
      Content
      Tester Connection
      D41-27 (SPD) - D48-11 (GND)
      Tool Setting
      5 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)