Home › Engine / Hybrid System › FA20 ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILLER CAP
  1. Remove the oil filler cap.



2. REMOVE OIL FILTER SUB-ASSEMBLY


    A281048E01
  1. Using SST, remove the oil filter sub-assembly.

    SST
    09228-22020  



3. REMOVE OIL FILTER UNION


    A281050
  1. Remove the oil filter union.



4. REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR


    A280837
  1. Using a 19 mm union nut wrench, remove the E.F.I. engine coolant temperature sensor.



5. REMOVE KNOCK CONTROL SENSOR


    A280838
  1. Remove the 2 bolts and 2 knock control sensors.



6. REMOVE CRANK POSITION SENSOR


    A280839
  1. Remove the bolt and crank position sensor.



7. REMOVE VVT SENSOR


    A280840
  1. Remove the bolt and VVT sensor (for intake side of bank 1).

  1. Remove the O-ring from the VVT sensor.



    A280841
  1. Remove the bolt and VVT sensor (for exhaust side of bank 1).

  1. Remove the O-ring from the VVT sensor.



    A280842
  1. Remove the bolt and VVT sensor (for intake side of bank 2).

  1. Remove the O-ring from the VVT sensor.



    A280843
  1. Remove the bolt and VVT sensor (for exhaust side of bank 2).

  1. Remove the O-ring from the VVT sensor.



8. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE


    A280844
  1. Remove the 2 bolts and camshaft timing oil control valve (for intake side of bank 1).



    A276534E01
  1. Remove the O-ring from the camshaft timing oil control valve.

  1. Remove the back-up ring from the camshaft timing oil control valve.
    Text in Illustration 
    *1
    O-ring
    *2
    Back-up Ring



    A280845
  1. Remove the 2 bolts and camshaft timing oil control valve (for exhaust side of bank 1).

  1. Remove the O-ring from the camshaft timing oil control valve.

  1. Remove the back-up ring from the camshaft timing oil control valve.



    A280846
  1. Remove the 2 bolts and camshaft timing oil control valve (for intake side of bank 2).

  1. Remove the O-ring from the camshaft timing oil control valve.

  1. Remove the back-up ring from the camshaft timing oil control valve.



    A280847
  1. Remove the 2 bolts and camshaft timing oil control valve (for exhaust side of bank 2).

  1. Remove the O-ring from the camshaft timing oil control valve.

  1. Remove the back-up ring from the camshaft timing oil control valve.



9. REMOVE ENGINE OIL TEMPERATURE SENSOR


    A280848E01
  1. Using a 19 mm deep socket wrench, remove the engine oil temperature sensor.

    NOTICE:
    Use a cloth or the like to prevent engine oil from splashing.

    Text in Illustration 
    *1
    19 mm Deep Socket Wrench



10. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A280849E01
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.

    NOTICE:
    Use a cloth or the like to prevent engine oil from splashing.

    Text in Illustration 
    *1
    24 mm deep socket wrench



11. REMOVE PCV HOSE CONNECTOR


    A280851
  1. Remove the 3 bolts and PCV hose connector.

  1. Loosen the 2 clips and remove the No. 2 water by-pass hose from the PCV hose connector.



12. REMOVE VACUUM PUMP ASSEMBLY (for Automatic Transmission)


    C260987
  1. Remove the 3 bolts and vacuum pump assembly.



    C262997E01
  1. Remove the O-ring.

  1. Remove the seal packing from the vacuum pump assembly and the engine.



13. REMOVE REAR CYLINDER HEAD PLATE (for Manual Transmission)


    C260986
  1. Remove the 3 bolts and rear cylinder head plate.



14. REMOVE WATER INLET PIPE


    A279573
  1. Disconnect the No. 3 water by-pass hose.

  1. Remove the 4 bolts and water inlet pipe.



    A280856
  1. Remove the 2 O-rings from the cylinder block.



15. REMOVE PCV VALVE SUB-ASSEMBLY


    A278795
  1. Using a 19 mm deep socket wrench, remove the PCV valve sub-assembly.



16. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A276069
  1. Remove the bolt, No. 1 idler pulley sub-assembly and idler pulley cover.



17. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A276070
  1. Remove the bolt, No. 1 idler pulley sub-assembly and idler pulley cover.



18. REMOVE WATER PUMP PULLEY


    A281162E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and water pump pulley.



19. REMOVE ENGINE WATER PUMP ASSEMBLY


    A279726
  1. Remove the 5 bolts, engine water pump assembly and gasket.



20. REMOVE WATER OUTLET


    A281051
  1. Remove the 2 bolts and water outlet.



21. REMOVE THERMOSTAT
  1. Remove the thermostat.

  1. Remove the gasket from the thermostat.



22. REMOVE CRANKSHAFT PULLEY


    A302560E01
  1. Install SST to the crankshaft pulley.

    SST
    09213-80010   (90179-10016, 09213-08010, 09213-08110)

    HINT:
    Position the projections on SST in the direction as shown in the illustration to prevent SST from separating from the crankshaft pulley.

    Text in Illustration 
    *1
    Claw



    A302561E01
  1. Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt.

    SST
    09213-80010   (90179-10016, 09213-08010, 09213-08110)
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Remove the crankshaft pulley.



    A276039
  1. Remove the O-ring and crankshaft pulley spacer.



23. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL


    A276038E01
  1. Using a screwdriver with its tip wrapped in protective tape, pry out the timing chain or belt cover oil seal.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    After the removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.

    HINT:
    Tape the screwdriver tip before use.



24. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


  1. Remove the 32 bolts.


    A281480



  1. Using a screwdriver with its tip wrapped in protective tape, remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and cylinder head or cylinder block.


    C257592E01


    Text in Illustration 
    *1
    Protective Tape
    -
    -

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block or chain cover.



  1. Remove the 4 O-rings.


    A281482



25. MAKE PAINT MARKS


HINT:
If the alignment marks are difficult to identify during the work, mark the alignment marks with paint at the positions shown in the illustration, for easier recognition.



A334212E01


Text in Illustration 
*a
Triangular Mark
*b
Engraved Line
*c
Oval Mark
*d
Crankshaft Timing Gear key


26. REMOVE CHAIN SUB-ASSEMBLY (for Bank 1)

CAUTION:
Do not remove the chain sub-assembly from bank 2 at the same time as the chain sub-assembly is being removed from bank 1. Otherwise, the camshaft on bank 2 may turn suddenly, which is dangerous.



    A334213
  1. Temporarily install the crankshaft pulley spacer and crankshaft pulley.



    A334218E01
  1. Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly RH and the camshaft timing exhaust gear assembly RH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

    SST
    09960-10010   (09962-01000, 09963-01000)
    Text in Illustration 
    *a
    Alignment Mark
    *b
    Crankshaft Pulley Pin Hole
    *c
    Crankshaft Timing Gear key

    HINT:
    At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.

  1. Remove the crankshaft pulley and crankshaft pulley spacer.



    A279526
  1. Push down the chain tensioner slipper and retain the plunger by inserting a 2.5 mm (0.098 in.) diameter hexagonal wrench into the No. 1 chain tensioner assembly through the stopper plate.



    A279527
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.

  1. Remove the chain tensioner slipper.



    A279528
  1. Using a 5 mm hexagonal wrench, remove the bolt and No. 1 chain vibration damper.

  1. Remove the chain sub- assembly (for bank 1).

    NOTICE:
    1. With the chain sub- assembly (for bank 1) removed, the valve heads may contact each other if the camshafts are turned, causing the valve stems to bend.
    2. To avoid this, do not turn the intake camshaft RH and the exhaust camshaft RH more than zero-lift range (The range where camshafts can be turned lightly by hand).

    HINT:
    Arrange the removed parts in the correct order.



27. REMOVE CHAIN SUB-ASSEMBLY (for Bank 2)
  1. Temporarily install the crankshaft pulley spacer and crankshaft pulley.



  1. Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly LH and the camshaft timing exhaust gear assembly LH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

    SST
    09960-10010   (09962-01000, 09963-01000)


    A334219E01


    Text in Illustration 
    *a
    Alignment Mark
    *b
    Crankshaft Pulley Pin Hole
    *c
    Crankshaft Timing Gear key
    *d
    Cylinder Block Guide Pin

    HINT:
    At this time, the crankshaft timing gear key is at the position shown in the illustration.

  1. Remove the crankshaft pulley and crankshaft pulley spacer.



    A279530
  1. Push the chain tensioner slipper and retain the plunger by inserting an approximately 1 mm (0.039 in.) diameter wire into the No. 2 chain tensioner assembly through the stopper plate .



    A279531
  1. Remove the 2 bolts and No. 2 chain tensioner assembly.

  1. Remove the chain tensioner slipper.



    A279532
  1. Remove the O-ring from the cylinder block.



    A279533
  1. Using a 5 mm socket hexagon wrench, remove the bolt and No. 1 chain vibration damper.



    A334220E01
  1. While releasing the tension of chain sub-assembly using SST, remove the chain sub-assembly.

    SST
    09960-10010   (09962-01000, 09963-00700)

    CAUTION:
    Make sure to use SST. Never carry out the work using only your hands.

    NOTICE:
    1. With the chain sub-assembly (for bank 2) removed, the valve heads may contact each other if the camshafts are turned, causing the valve stems to bend. To avoid this, do not turn the exhaust camshaft LH more than zero-lift rang (The range where the camshaft can be turned lightly by hand).
    2. At this time, No. 1 and No. 4 pistons are located near TDC. If the intake camshaft is turned, the valves may come into contact with the piston, causing the valve stems to bend. To avoid this, do not turn the intake camshaft LH.

    HINT:
    Arrange the removed parts in the correct order.



28. ROTATE CRANK SHAFT AND CAMSHAFT
  1. Temporarily install the crankshaft pulley spacer and crankshaft pulley.



    A334223E01
  1. Using SST, turn the crankshaft about 200 degrees counterclockwise until the crankshaft pulley pin hole is aligned at the position shown in the illustration.

    SST
    09960-10010   (09962-01000, 09963-01000)
    Text in Illustration 
    *a
    Crankshaft Pulley Pin Hole
    *b
    Alignment Mark
    *c
    Crankshaft Timing Gear Key

    NOTICE:
    Do not turn the crankshaft counterclockwise except for a slight adjustment to correctly align the alignment mark. If not, the valves may come into contact with the piston.

    HINT:
    At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.

  1. Remove the crankshaft pulley and crankshaft pulley spacer.



    A279535E02
  1. Using SST, turn the camshaft timing intake gear assembly LH approximately 180°clockwise, and align the alignment mark on the camshaft timing intake gear assembly LH to the position (zero-lift position) shown in the illustration.
    Text in Illustration 
    *a
    Alignment Mark

    SST
    09960-10010   (09962-01000, 09963-00700)

    NOTICE:
    After this work, when the intake valve and exhaust valve lift at the same time, the valve heads contact each other, causing the valve stems to bend. To avoid this, do not turn the intake camshaft LH and the exhaust camshaft LH more than the zero-lift range (the range where the camshafts can be turned lightly by hand).



29. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET


    A279563
  1. Remove the crankshaft timing gear or sprocket.



30. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY RH


    A279551E01
  1. Using SST, hold the camshaft timing intake gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the camshaft timing intake gear assembly RH.



31. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH


    A279552E01
  1. Using SST, hold the camshaft timing exhaust gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the camshaft timing exhaust gear assembly RH.



32. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY LH


    A279553E01
  1. Using SST, hold the camshaft timing intake gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the camshaft timing intake gear assembly LH.



33. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH


    A279554E01
  1. Using SST, hold the camshaft timing exhaust gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the camshaft timing exhaust gear assembly LH.



34. REMOVE SPARK PLUG
  1. Using a 14 mm spark plug wrench, remove the 4 spark plugs.



35. REMOVE INJECTOR DRIVER BRACKET


    A283322
  1. Remove the 2 bolts and injector driver bracket.



36. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Operate the engine stand so that the bank 1 side faces upward.



    A283323
  1. Remove the 8 bolts.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the cylinder head cover sub-assembly RH.

    NOTICE:
    Do not damage the camshaft housing sub-assembly RH, cam caps and cylinder head cover sub-assembly RH.

  1. Remove the cylinder head cover gasket.



    A283324
  1. Remove the 2 spark plug tube gaskets.

    NOTICE:
    When removing the seal packing left on the camshaft housing sub-assembly RH using a scraper, use special care not to damage the camshafts.



37. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

NOTICE:
Do not remove the intake and exhaust camshafts first as it may cause a deformation of the cylinder head sub-assembly.



    A283325E01
  1. Loosen the 9 bolts in the order shown in the illustration and remove them.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly RH.

    NOTICE:
    Do not damage the cylinder head sub-assembly RH and camshaft housing sub-assembly RH.



    A278733
  1. Remove the 2 O-rings and 8 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

    HINT:
    Arrange the removed parts in the correct order.



    A278734
  1. Remove the 8 valve adjusting shims and 8 roller rocker arm pivots from the cylinder head sub-assembly.

    HINT:
    1. Arrange the removed parts in the correct order.
    2. When installing, be sure to install the removed parts in their original locations.



38. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH


    A278735E01
  1. Loosen the 6 bolts in the order shown in the illustration.

  1. Lightly tap the cylinder head sub-assembly RH to separate it from the cylinder block (bank 1).

  1. Remove the cylinder head sub-assembly RH.

    NOTICE:
    Be careful not to scratch the mating surface of the cylinder head and cylinder block.



39. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head gasket.



40. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Operate the engine stand so that the bank 2 side faces upward.



    A279567
  1. Remove the 8 bolts.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the cylinder head cover sub-assembly LH.

    NOTICE:
    Do not damage the camshaft housing sub-assembly LH, cam caps and cylinder head cover sub-assembly LH.

  1. Remove the cylinder head cover gasket.



    A279568
  1. Remove the 2 spark plug tube gaskets.

    NOTICE:
    When removing the seal packing left on the camshaft housing sub-assembly LH using a scraper, use special care not to damage the camshafts.



41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

NOTICE:
Do not remove the intake and exhaust camshafts first as it may cause a deformation of the camshaft housing sub-assembly LH.



    A283326E01
  1. Loosen the 9 bolts in the order shown in the illustration and remove them.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly LH.

    NOTICE:
    Do not damage the cylinder head sub-assembly LH and camshaft housing sub-assembly LH.



    A278737
  1. Remove the 2 O-rings and 8 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly LH.

    HINT:
    Arrange the removed parts in the correct order.



    A278738
  1. Remove the 8 valve adjusting shims and 8 roller rocker arm pivots from the cylinder head sub-assembly LH.

    HINT:
    1. Arrange the removed parts in the correct order.
    2. When installing, be sure to install the removed parts in their original locations.



42. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH


    A278739E01
  1. Loosen the 6 bolts in the order shown in the illustration.

  1. Lightly tap the cylinder head sub-assembly LH to separate it from the cylinder block (bank 2).

  1. Remove the cylinder head sub-assembly LH.

    NOTICE:
    Be careful not to scratch the mating surface of the cylinder head and cylinder block.



43. REMOVE NO. 2 CYLINDER HEAD GASKET
  1. Remove the No. 2 cylinder head gasket.



44. REMOVE NO. 2 ENGINE HANGER


A279574
  1. Remove the 2 bolts and No. 2 engine hanger from the cylinder block (for bank 1).



45. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket.



    A278797
  1. Remove the 11 bolts.



    A120816
  1. Using an oil pan seal cutter, remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Do not damage the contact surface and flange part of the No. 2 oil pan sub-assembly.



    A279593
  1. Remove the 2 seal rings from the No. 2 oil pan sub-assembly.



46. REMOVE OIL STRAINER SUB-ASSEMBLY


    A278798
  1. Remove the 2 bolts and oil strainer sub-assembly.

  1. Remove the O-ring.



47. REMOVE OIL PAN SUB-ASSEMBLY


    A281037
  1. Remove the 13 bolts.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pan sub-assembly.

    NOTICE:
    Do not damage the cylinder block and oil pan sub-assembly.



    A278741
  1. Remove the 3 O-rings from the cylinder block.



    A279598
  1. Remove the 4 bolts and baffle plate from the oil pan sub-assembly.



    A279592
  1. Remove the 2 stud bolts from the oil pan sub-assembly.



48. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


    A278744E01
  1. In several steps, uniformly loosen the 12 bolts in the order shown in the illustration, and remove the front camshaft cap RH, intake center camshaft cap RH, intake rear camshaft cap RH, exhaust center camshaft cap RH, and exhaust rear camshaft cap RH.

    HINT:
    Arrange the removed parts in the correct order.



49. REMOVE CAMSHAFT (for Bank 1)


    A278745
  1. Remove the intake camshaft RH and exhaust camshaft RH from the camshaft housing sub-assembly RH.



50. REMOVE OIL CONTROL VALVE FILTER (for Bank 1)


    A278746
  1. Remove the 2 oil control valve filters from the camshaft housing sub-assembly RH.



51. REMOVE OIL SPACER RH


    A279590
  1. Remove the 2 bolts and oil spacer RH.



52. REMOVE CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY (for Automatic Transmission)


    A278793
  1. Remove the 2 union bolts, the bolt, camshaft oil feed pipe sub-assembly and 2 gaskets from the camshaft housing sub-assembly RH.



53. REMOVE HOLE PLUG (for Manual Transmission)


    A278792
  1. Remove the hole plug and gasket from the camshaft housing sub-assembly RH.



54. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


    A278747E01
  1. In several steps, uniformly loosen the 13 bolts in the order shown in the illustration, and remove the front camshaft cap LH, intake center camshaft cap LH, intake rear camshaft cap LH, exhaust center camshaft cap LH and exhaust rear camshaft cap LH.

    HINT:
    Arrange the removed parts in the correct order.



55. REMOVE CAMSHAFT (for Bank 2)


    A278748
  1. Remove the intake camshaft LH and exhaust camshaft LH from the camshaft housing sub-assembly LH.



56. REMOVE OIL CONTROL VALVE FILTER (for Bank 2)


    A278789
  1. Remove the 2 oil control valve filters from the camshaft housing sub-assembly LH.



57. REMOVE OIL SPACER LH


    A279591
  1. Remove the 2 bolts and oil spacer LH.