Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311513E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Disconnect the D5 main body ECU (network gateway ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D5-22 (ACC) - Body ground*1
    W - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V

    1. *1: w/ Entry and Start System

  3. Disconnect the 3A, 3C, 3E, A73 and D6 instrument panel junction block assembly and main body ECU (network gateway ECU) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-15 - Body ground
    W - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    3A-20 - Body ground
    SB - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    3A-27 - Body ground
    G-R - Body ground
    Battery power supply
    Always
    11 to 14 V
    3C-19 - Body ground
    L-R - Body ground
    Battery power supply
    Always
    11 to 14 V
    3E-1 - Body ground
    B-R - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  5. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-12 - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    3A-13 - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    A73-4 (GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω
    D6-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  6. Reconnect the 3A, 3C, 3E, A73 and D6 instrument panel junction block assembly and main body ECU (network gateway ECU) connectors.

  7. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-28 - Body ground
    V - Body ground
    Front door courtesy light switch LH input*3
    Front door courtesy light switch RH input*4
    Front door LH open*3
    Front door RH open*4
    Below 1 V
    Front door LH closed*3
    Front door RH closed*4
    11 to 14 V
    3B-13 - Body ground
    GR - Body ground
    Front door courtesy light switch RH input*3
    Front door courtesy light switch LH input*4
    Front door RH open*3
    Front door LH open*4
    Below 1 V
    Front door RH closed*3
    Front door LH closed*4
    11 to 14 V
    3D-26 - Body ground
    SB - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door open
    Below 1 V
    Luggage compartment door closed
    11 to 14 V
    D5-5 (FLCL) - Body ground*3
    D5-5 (FRCL) - Body ground*4
    SB - Body ground
    Front door courtesy light LH drive output*3
    Front door courtesy light RH drive output*4
    Ignition switch off, front door courtesy light LH off*3
    Ignition switch off, front door courtesy light RH off*4
    11 to 14 V
    Ignition switch off, front door courtesy light LH on*3
    Ignition switch off, front door courtesy light RH on*4
    Below 1 V
    D5-6 (FRCL) - Body ground*3
    D5-6 (FLCL) - Body ground*4
    B - Body ground
    Front door courtesy light RH drive output*3
    Front door courtesy light LH drive output*4
    Ignition switch off, front door courtesy light RH off*3
    Ignition switch off, front door courtesy light LH off*4
    11 to 14 V
    Ignition switch off, front door courtesy light RH on*3
    Ignition switch off, front door courtesy light LH on*4
    Below 1 V
    D5-7 (DOMR) - Body ground
    L - Body ground
    Illuminated entry drive output (to map light assembly)
    Map light switch in DOOR position and map light assembly on
    Below 1 V
    Map light switch in DOOR position and map light assembly off
    11 to 14 V
    D5-28 (ILL) - Body ground*2
    Y - Body ground
    Ignition key cylinder light drive output
    Ignition switch off, ignition key cylinder light off (when operated by illuminated entry system)
    11 to 14 V
    Ignition switch off, ignition key cylinder light on (when operated by illuminated entry system)
    Below 1 V
    D6-11 (LSFD) - Body ground*1
    W - Body ground
    Front door unlock detection switch LH input*3
    Front door unlock detection switch RH input*4
    Ignition switch off, all doors closed and front door LH locked*3
    Ignition switch off, all doors closed and front door RH locked*4
    Pulse generation
    Front door LH unlocked*3
    Front door RH unlocked*4
    Below 1 V
    D6-12 (LSFP) - Body ground*1
    SB - Body ground
    Front door unlock detection switch RH input*3
    Front door unlock detection switch LH input*4
    Ignition switch off, all doors closed and front door RH locked*3
    Ignition switch off, all doors closed and front door LH locked*4
    Pulse generation
    Front door RH unlocked*3
    Front door LH unlocked*4
    Below 1 V

    1. *1: w/ Entry and Start System
    2. *2: w/o Entry and Start System
    3. *3: for LHD
    4. *4: for RHD
    If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E41

  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D41-5 (IG2) - Body ground
    Y - Body ground
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    D48-2 (+B) - D48-11 (GND)
    R - B
    +B power supply
    Always
    9.5 to 16 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  5. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D41-16 (SWIL) - D41-24 (AGND)
    LG - B
    Engine switch illumination drive output
    Engine switch illumination on
    11 to 14 V
    Engine switch illumination off
    Below 1 V
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.