Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the GTS on.

  5. Enter the following menus: Chassis / EMPS / Trouble Codes.

  6. According to the display on the GTS, select the freeze frame data.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from skid control ECU/
    Min.: 0.0 km/h (0.0 mph)
    Max.: 300.0 km/h (186.4 mph)
    0 km/h (0 mph)
    The vehicle is stopped.
    No significant fluctuation
    The vehicle is driven at a constant speed.
    Engine Revolution
    Engine speed/
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    The engine is running at a constant speed.
    Motor Actual Current
    Amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    The engine is running and the steering wheel is being turned.
    Command Value Current
    Demanded amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    The engine is running and the steering wheel is being turned.
    Steering Angle Velocity
    Steering angle speed/
    Min.: -32768 deg/s
    Max.: 32767 deg/s
    Value changes in proportion to steering effort
    The engine is running and the steering wheel is being turned.
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -50.0°C (-58.0°F)
    Max.: 150.0°C (302.0°F)
    -
    The ignition switch is ON.
    PIG Power Supply
    Power source voltage to active motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    The engine is running and power steering is operating.
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    The ignition switch is ON.
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -7.00 Nm
    Max.: 7.00 Nm
    Value changes in proportion to steering effort
    The engine is running and the steering wheel is being turned.
    Motor Rotation Angle
    Motor rotation angle/
    Min.: 0.000 deg
    Max.: 360.000 deg
    Motor rotation angle value changes from 0 to 360 deg
    The engine is running and the steering wheel is being turned.
    Command Val Current 2
    Demanded amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    The engine is running and the steering wheel is being turned.
    PIG2 Voltage
    Coil rear pressurization voltage/
    Min.: 0.000 V
    Max.: 98.000 V
    Approximately 27 V
    The engine is running and the steering wheel is not being turned.
    Value changes between 16 and 35 V
    The engine is running and the steering wheel is being turned.
    Motor Voltage
    Motor power supply voltage/
    Min.: 0.000 V
    Max.: 98.000 V
    Approximately 27 V
    The engine is running and the steering wheel is not being turned.
    Value changes between 4 and 35 V
    The engine is running and the steering wheel is being turned.
    Motor Terminal Volt(U)
    Motor terminal voltage (U phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes between 4 and 35 V
    The engine is running and the steering wheel is being turned.
    Motor Terminal Volt(V)
    Motor terminal voltage (V phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes between 4 and 35 V
    The engine is running and the steering wheel is being turned.
    Motor Terminal Volt(W)
    Motor terminal voltage (W phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes between 4 and 35 V
    The engine is running and the steering wheel is being turned.
    Torque Sensor 1 Output
    Torque sensor 1 output voltage/
    Min.: 0.0000 V
    Max.: 5.0000 V
    2.3 to 2.7 V
    The engine is running and the steering wheel is not turned (without load).
    2.3 to 3.8 V
    The engine is running and the steering wheel is turned to the right when the vehicle is stopped.
    1.2 to 2.7 V
    The engine is running and the steering wheel is turned to the left when the vehicle is stopped.
    Torque Sensor 2 Output
    Torque sensor 2 output voltage/
    Min.: 0.0000 V
    Max.: 5.0000 V
    2.3 to 2.7 V
    The engine is running and the steering wheel is not turned (without load).
    1.2 to 2.7 V
    The engine is running and the steering wheel is turned to the right when the vehicle is stopped.
    2.3 to 3.8 V
    The engine is running and the steering wheel is turned to the left when the vehicle is stopped.
    TRQ1 Zero Point Value
    Torque sensor 1 zero point voltage/
    Min.: 0.0000 V
    Max.: 5.0000 V
    Values differ depending on vehicle
    The engine is running and the steering wheel is not being turned.
    TRQ2 Zero Point Value
    Torque sensor 2 zero point voltage/
    Min.: 0.0000 V
    Max.: 5.0000 V
    Values differ depending on vehicle
    The engine is running and the steering wheel is not being turned.