Home › Engine / Hybrid System › FA20 COOLING › COOLING FAN MOTOR

COOLING FAN MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 COOLING FAN MOTOR (w/ Air Conditioning System)
  1. Install the No. 2 cooling fan motor with the 3 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



2. INSTALL COOLING FAN MOTOR (w/ Air Conditioning System)
  1. Install the cooling fan motor with the 3 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

  1. Connect the wire harness to the 2 cooling fan motors.



3. INSTALL COOLING FAN MOTOR (w/o Air Conditioning System)
  1. Install the cooling fan motor with the 3 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



4. INSTALL NO. 2 FAN (w/ Air Conditioning System)
  1. Install the No. 2 fan with the nut.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }



5. INSTALL FAN
  1. Install the fan with the nut.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }



6. INSTALL FAN SHROUD

HINT:
Insert a cardboard or a blanket between the radiator assembly and the fan shroud to protect the radiator assembly.

  1. Engage the fitting sections in the bottom of the fan shroud with the fitting sections of the radiator assembly.

    NOTICE:
    Do not damage the outlet radiator hose, inlet radiator hose, No. 1 radiator hose, water filler sub-assembly, or air conditioner tube and accessory assembly.

  1. Attach the 2 claws and install the fan shroud to the radiator assembly.

  1. Connect the 2 cooling fan motor connectors and 2 clamps to the radiator assembly.



7. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY
  1. Install the 6 bolts and radiator support sub-assembly.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



8. INSTALL RADIATOR COVER PLATE
  1. Install the radiator cover plate with the 6 clips.



9. REMOVE AIR CLEANER DUCT
  1. Install the air cleaner duct with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



10. CONNECT HOOD LOCK ASSEMBLY (for LHD)
  1. Apply MP grease to the sliding areas of the hood lock assembly.



    B313111
  1. Connect the hood lock control cable assembly to the hood lock assembly.



    B313112E02
  1. Install the hood lock assembly with the 3 bolts in the order shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



11. CONNECT HOOD LOCK ASSEMBLY (for RHD)
  1. Apply MP grease to the sliding areas of the hood lock assembly.



    B310946
  1. Connect the hood lock control cable assembly to the hood lock assembly.



    B310947E03
  1. Install the hood lock assembly with the 3 bolts in the order shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



12. INSTALL WATER FILLER SUB-ASSEMBLY
  1. Install the water filler sub-assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



13. INSTALL RADIATOR RESERVE TANK ASSEMBLY
  1. Install the radiator reserve tank assembly with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



14. INSTALL FRONT BUMPER COVER
(Click here)


15. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner duct with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }