Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)

DTC    B1242    Wireless Door Lock Tuner Circuit Malfunction

for Preparation Click here


DESCRIPTION

The door control receiver is used to receive electrical waves relating to the entry functions of the entry and start system. The certification ECU (smart key ECU assembly) decodes the requested entry and start system operation by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU).

DTC No.
DTC Detection Condition
Trouble Area
B1242
  1. Short in RDA or RSSI to ground between the certification ECU (smart key ECU assembly) and the door control receiver.
  2. Short in RDA or RSSI to ground when RC0 (12 V) output from the ECU is off.
  1. Door control receiver
  2. Wire harness or connector
  3. Certification ECU (Smart Key ECU Assembly)

WIRING DIAGRAM


B265620E05


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  2. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  3. When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

1.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B272823E03
  1. Disconnect the H26 door control receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H26-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H26-4 (+5) - H26-1 (GND)
    Always
    Below 1 V → 4.5 to 5.5 V (Pulse generation)
    H26-2 (RSSI) - H26-1 (GND)
    Always
    11 to 14 V
    H26-5 (DATA) - H26-1 (GND)
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
REPLACE DOOR CONTROL RECEIVER (Click here)
A


2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU))
  1. Disconnect the D40 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-19 (RSSI) - H26-2 (RSSI)
    Always
    Below 1 Ω
    D40-17 (RDA) - H26-5 (DATA)
    Always
    Below 1 Ω
    D40-5 (RCO) - H26-4 (+5)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)