ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch status / OFF or ON | OFF: Engine switch off ON: Engine switch on (IG) | Use this Data List item to help determine the cause when all the entry and start system/wireless functions do not operate. |
| Immobilizer when IG=ON | Engine immobiliser system status when power source mode on (IG) / UNSET or SET | UNSET: Engine immobiliser system not set with engine switch on (IG) or engine immobiliser system unset for 40 times after engine immobiliser system set SET: Engine immobiliser system set (driver door open and closed with engine switch on (IG)) | - |
| Immobiliser | Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset | Set: Engine immobiliser set (engine start prohibited) (engine switch off) Unset: Engine immobiliser unset (engine start permitted) [engine switch on (ACC) or on (IG)] | If "Set" is displayed, the engine start function is prohibited. |
| Master Key | Whether master key ID code matches ID code registered in certification ECU (smart key ECU assembly) / No Match or Match | No Match: ID code of master key does not match ID code registered in certification ECU (smart key ECU assembly) Match: ID code of master key matches ID code registered in certification ECU (smart key ECU assembly) |
|
| Sub Key | Whether sub-key ID code matches ID code registered in certification ECU (smart key ECU assembly) / No Match or Match | Match: ID code of sub key matches ID code registered in certification ECU (smart key ECU assembly) No Match: ID code of sub key does not match ID code registered in certification ECU (smart key ECU assembly) |
|
| BCC Malfunction | BCC signal status of transponder chip*1 / OK or NG | OK: BCC signal normal NG: BCC signal malfunction (malfunction in code computation in key/certification ECU (smart key ECU assembly) | Problems may be caused by the following:
|
| Abnormal Status | Transponder chip status signal*1 / OK or NG | OK: Transponder chip status signal normal NG: Transponder chip status signal malfunction (malfunction in code computation in key/ certification ECU (smart key ECU assembly)) | Problems may be caused by the following:
|
| Different Encrypt Code | Code status between transponder chip and certification ECU (smart key ECU assembly)*1 / OK or NG | OK: Codes of transponder chip and certification ECU (smart key ECU assembly) match NG: Codes of transponder chip and certification ECU (smart key ECU assembly) do not match | Problems may be caused by the following:
|
| Different Serial Number | Vehicle serial number*1 / OK or NG | OK: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) match NG: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) do not match | Problems may be caused by the following:
|
| Frame Error | State of data sent from electrical key transmitter sub-assembly / OK or NG | OK: No problem with data sent from electrical key transmitter sub-assembly NG: Problem with data sent from electrical key transmitter sub-assembly |
|
| Response | Electrical key transmitter sub-assembly response to signal from certification ECU (smart key ECU assembly) / OK or NG | OK: Electrical key transmitter sub-assembly responds to signal from certification ECU (smart key ECU assembly) NG: Electrical key transmitter sub-assembly does not respond to signal from certification ECU (smart key ECU assembly) | Problems may be caused by the following:
|
| ID-BOX Sleep Condition | ID code box (immobiliser code ECU) sleep mode status / No or Yes | No: ID code box (immobiliser code ECU) sleep mode not possible Yes: ID code box (immobiliser code ECU) sleep mode possible | - |
| ID-BOX Start Condition | ID code box (immobiliser code ECU) status*3 / No or Yes | No: Wake-up signal not sent by ID code box (immobiliser code ECU) Yes: Wake-up signal sent by ID code box (immobiliser code ECU) | - |
| Engine Start Request | Request from certification ECU (smart key ECU assembly) to ID code box (immobiliser code ECU) to permit ECM to start engine*3 / OK or NG | OK: Engine start permission request signal from certification ECU (smart key ECU assembly) received by ID code box (immobiliser code ECU)*9 or certification ECU (smart key ECU assembly)*10 NG: Engine start permission request signal not received by ID code box (immobiliser code ECU)*9 or certification ECU (smart key ECU assembly)*10 | If OK is not displayed, the immobiliser cannot be unset by the ECM. |
| S Code Check*9 | S code verification result*4 / OK or NG | OK: S code verification result normal NG: S code verification result abnormal | Problems may be caused by the following:
|
| L Code Check | L code verification result*5 / OK or NG | OK: L code verification result normal NG: L code verification result abnormal | Problems may be caused by the following:
|
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly)*6 / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed) NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed) | If OK is not displayed even when the steering lock unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly)*7 / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P*11 and engine switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P*11 and engine switch off) | If OK is not displayed even when the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| S Code Check (Past) | S code verification result (past) / OK or NG(Past) | OK: Verification confirmed (past) NG(Past): Verification not confirmed (past) | - |
| L Code Check (Past) | L code verification result (past) / OK or NG(Past) | OK: Verification confirmed (past) NG(Past): Verification not confirmed (past) | - |
| EFI/EGI Code Receive | Certification information sent to ID code box (immobiliser code ECU) from ECM when ECM receives engine start permission signal from ID code box (immobiliser code ECU)*8 / OK or NG | OK: Signal from ECM to unset engine immobiliser received by ID code box (immobiliser code ECU)*9 or certification ECU (smart key ECU assembly)*10 NG: Signal from ECM to unset engine immobiliser not received by ID code box (immobiliser code ECU)*9 or certification ECU (smart key ECU assembly)*10 | - |
| EFI Communication | State of communication to unset immobiliser between certification ECU (smart key ECU assembly) and ECM / NG or OK | NG: Communication to unset immobiliser has not started between certification ECU (smart key ECU assembly) and ECM OK: Communication to unset immobiliser has started between certification ECU (smart key ECU assembly) and ECM | If the item displays "NG" even though the conditions to unset the immobiliser have been met and the Engine Start Request Data List item displays "OK", the ECM may be malfunctioning. When the engine cannot be started, use this Data List item during troubleshooting. |
| #Codes | Number of trouble codes / Min: 0, Max: 255 | Number of stored DTCs displayed | - |

| ACTIVE TEST |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Security Indicator | Security indicator light | ON/OFF | - |