Home › Drivetrain ยท TL70 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 3 GEAR SHIFT FORK SHAFT


    C260035
  1. Install the No. 3 gear shift fork shaft to the No. 3 gear shift fork with a new bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



2. INSTALL NO. 1 GEAR SHIFT FORK SHAFT


    C258440
  1. Install the No. 1 gear shift fork shaft to the No. 1 gear shift fork with a new bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    C258441
  1. Using a brass bar and a hammer, install a new shaft snap ring.



    C258442
  1. Install the No. 1 gear shift fork shaft together with the No. 1 gear shift fork to the No. 3 gear shift fork shaft and No. 3 gear shift fork.



    C260036
  1. Using a brass bar and a hammer, install a new shaft snap ring.



3. INSTALL NO. 2 GEAR SHIFT FORK SHAFT


    C258436
  1. Install the No. 2 gear shift fork shaft to the No. 2 gear shift fork with a new bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    C258443
  1. Using a brass bar and a hammer, install a new shaft snap ring.



4. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL


    C257041E01
  1. Using SST and a hammer, install a new transmission front bearing retainer oil seal.

    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07100)

    Installation depth:
    11.1 to 11.9 mm (0.437 to 0.469 in.) (from the end surface of the front bearing retainer)

    NOTICE:
    1. Do not damage the lip of the transmission front bearing retainer oil seal.
    2. Do not damage the front bearing retainer.

  1. Apply MP grease to the lip of the transmission front bearing retainer oil seal.



5. INSTALL REVERSE IDLER GEAR SHAFT


    C257111
  1. Apply manual transmission gear oil to the reverse idle gear shaft, and then install it to the reverse idler gear.



6. INSTALL INPUT SHAFT


    C258452
  1. Apply manual transmission gear oil to the needle roller bearing of the input shaft, and then install the input shaft to the output shaft.



7. INSTALL COUNTER SHAFT


  1. Install the input shaft, output shaft, counter shaft, reverse idler gear, reverse idler gear shaft, No. 1 gear shift fork shaft, No. 2 gear shift fork shaft and No. 3 gear shift fork shaft all together to the clutch housing.


    C257308



    C258433
  1. Using a new gasket and a new bolt, temporarily install the reverse idler gear shaft (clutch housing side).



    C258432
  1. Using a snap ring expander, install 2 new shaft snap rings.

    HINT:
    Install the shaft snap rings to the input shaft and counter shaft.



8. INSTALL FRONT BEARING RETAINER


    C266436
  1. Apply seal packing 1281 continuously to the front bearing retainer as shown in the illustration.
    Text in Illustration 
    V100143
    Seal Packing 1281

    NOTICE:
    Install it within 10 minutes of the seal packing application.



    P000601E16
  1. Apply adhesive 1344 to the 2nd and 3rd pitches from the tip of new bolt.
    Text in Illustration 
    *1
    Adhesive 1344



    C258431
  1. Install the front bearing retainer with the 7 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Install the front bearing retainer ensuring that the transmission front bearing retainer oil seal lip is not damaged.



9. INSTALL OIL RECEIVER PIPE


    C266428E01
  1. Install the oil receiver pipe.

    NOTICE:
    Confirm that the protrusions of the oil receiver pipe are properly fitted in the grooves.

    Text in Illustration 
    *a
    Protrusion



10. INSTALL TRANSMISSION CASE


    C266437
  1. Apply seal packing 1281 continuously to the transmission case as shown in the illustration.
    Text in Illustration 
    V100143
    Seal Packing 1281

    NOTICE:
    Install within 10 minutes of the seal packing application.



    C266429
  1. Check the location of the knock pin, and then using a plastic hammer, install the transmission case.
    Text in Illustration 
    V100144
    Do not hit hard.



    P000601E17
  1. Apply adhesive 1324 to the 2nd and 3rd pitches.
    Text in Illustration 
    *1
    Adhesive 1324



    C258428E02
  1. Install the transmission case and clamp with the 9 bolts.
    Text in Illustration 
    *1
    clamp

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    C258427
  1. Install a new reverse idler gear shaft fixing bolt and new gasket (transmission case side).

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    C258444
  1. Securely tighten the reverse idler gear shaft fixing bolt (clutch housing side).

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    C258426
  1. Using a snap ring expander, install a new shaft snap ring.



11. INSTALL REAR BEARING RETAINER


    C258425
  1. Install the shift arm pivot to the rear bearing retainer.



    P000601E17
  1. Apply adhesive 1324 to the 2nd and 3rd pitches from the tip of new bolt.
    Text in Illustration 
    *1
    Adhesive 1324



    C258424
  1. Using a T45 "TORX" socket wrench, install the rear bearing retainer with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



12. INSTALL 6TH GEAR THRUST WASHER


    C266867
  1. Install the straight pin to the counter shaft.



    C266868E01
  1. Apply manual transmission gear oil to the 6th gear thrust washer.
    Text in Illustration 
    *1
    6th Gear Thrust Washer
    V100135
    Front Side

  1. As shown in the illustration, install the 6th gear thrust washer to the counter shaft.



13. INSTALL NEEDLE ROLLER BEARING


    C266869
  1. Apply manual transmission gear oil to the needle roller bearing, and then install the needle roller bearing to the counter shaft.



14. INSTALL COUNTER SHAFT 6TH GEAR


    C266870
  1. Apply manual transmission gear oil to the counter shaft 6th gear, and then install the counter shaft 6th gear to the counter shaft.



15. INSTALL NO. 2 SYNCHRONIZER RING


    C266871
  1. Apply manual transmission gear oil to the No. 2 synchronizer ring, and then install the No. 2 synchronizer ring to the counter shaft.



16. INSTALL NO. 4 TRANSMISSION HUB SLEEVE


    C321948E01
  1. Apply manual transmission gear oil to the moving parts of the No. 4 transmission clutch hub.
    Text in Illustration 
    *1
    No. 4 Transmission Clutch Hub
    *2
    No. 4 Transmission Hub Sleeve
    *3
    Ball
    *4
    No. 1 Synchromesh Shifting Key
    *5
    No. 1 Synchromesh Shifting Key Spring
    V100135
    Front Side

  1. As shown in the illustration, install the No. 4 transmission hub sleeve to the No. 4 transmission clutch hub, and install the 3 No. 1 synchromesh shifting keys and 3 No. 1 synchromesh shifting key springs all together, and then install the 3 balls.

    HINT:
    1. Install the ball while holding down the No. 1 synchromesh shifting key spring.
    2. After the installation, settle the No. 1 synchromesh shifting key spring.



    C259267
  1. Install a new hole snap ring.



17. INSTALL NO. 4 TRANSMISSION CLUTCH HUB


    C266873E01
  1. Using SST and a press, install the No. 4 transmission clutch hub, No. 4 transmission hub sleeve, and No. 4 gear shift fork all together.

    SST
    09632-36010  

    HINT:
    1. Align the No. 4 transmission clutch hub and the No. 2 synchronizer ring so that they can fit together.
    2. Engage the No. 4 gear shift fork with the groove of the No. 4 transmission hub sleeve.



18. INSTALL SHAFT SNAP RING


    C266874
  1. Select a shaft snap ring that is suitable to retain the specific thrust clearance between the No. 4 transmission clutch hub and shaft snap ring.

    Standard clearance:
    0 to 0.1 mm (0 to 0.00394 in.)

    HINT:
    Select the thickest shaft snap ring possible for installation.

    Shaft Snap Ring Thickness 
    Part No.
    Thickness mm (in.)
    Mark
    SU003-03552
    2.80 (0.11023)
    A
    SU003-03553
    2.85 (0.11220)
    B
    SU003-03554
    2.90 (0.11417)
    C
    SU003-03555
    2.95 (0.11614)
    D
    SU003-03556
    3.00 (0.11811)
    E
    SU003-03557
    3.05 (0.12007)
    F



    C266875
  1. Using a brass bar and a hammer, install a new shaft snap ring to the counter shaft.



19. INSTALL NO. 2 GEAR SHIFT HEAD


    C266866
  1. Install the No. 2 gear shift head to the No. 2 gear shift fork shaft.

  1. Using a 5 mm pin punch and a hammer, install a new slotted spring pin to the No. 2 gear shift fork shaft.

    NOTICE:
    Do not tap the pin too deep.

    Standard depth:
    0 mm (0 in.) (from the end surface of the No. 2 gear shift head)



20. INSTALL 5TH SHIFT HEAD


    C257314
  1. Install the compression spring to the 5th shift head, and then, while holding down the ball with the 5 mm pin punch, install the 5th shift head to the No. 3 gear shift fork shaft.



    C266545
  1. Install the washer.



    C266876
  1. Using a brass bar and a hammer, install a new shaft snap ring to the No. 3 gear shift fork shaft.



21. INSTALL NO. 3 GEAR SHIFT FORK SHAFT


    C266872
  1. As shown in the illustration, insert the No. 3 gear shift fork shaft. Using a T40 "TORX" socket wrench, install the ball and compression spring, and then tighten with a new head straight screw plug.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



22. INSTALL SHIFT ARM


    C257331
  1. Install the shift arm to the shift arm pivot.



    C258445
  1. Using a brass bar and a hammer, install a new E- ring to the shift arm pivot.



23. INSTALL NO. 2 GEAR SHIFT FORK SHAFT


    C266877
  1. Using a screwdriver, install the 2 balls to the No. 3 gear shift fork shaft.

    HINT:
    Support the ball with the screwdriver so that the ball does not fall off.



    C266878E01
  1. While the identification hole is facing towards the outside, insert the No. 2 gear shift fork shaft. And then, using a T40 "TORX" socket wrench, install the ball and compression spring, and then tighten 2 new head straight screw plugs.
    Text in Illustration 
    *a
    Identification Hole

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



  1. for Pin:



      C266879
    1. Using a 5 mm pin punch and a hammer, install a new slotted spring pin to the No. 2 gear shift fork shaft.

      NOTICE:
      Do not tap the pin too deep.

      Standard depth:
      0 mm (0 in.) (from the end surface of the No. 4 gear shift fork)



  1. for Bolt:



      C318111
    1. Install a new bolt to the No. 2 gear shift fork shaft.

      Torque:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }



24. INSTALL NO. 3 GEAR SHIFT HEAD


    C266547
  1. Install the No. 3 gear shift head to the No. 3 gear shift fork shaft.

    HINT:
    While rotating, install the No. 3 gear shift head so that the shift arm is engaged with the groove of the No. 3 gear shift head.

  1. Using a 5 mm pin punch and a hammer, install a new slotted spring pin to the No. 3 gear shift fork shaft.

    NOTICE:
    Do not tap the pin too deep.

    Standard depth:
    0 mm (0 in.) (from the end surface of the No. 3 gear shift head)



25. INSTALL NO. 1 GEAR SHIFT HEAD


    C266548
  1. Install the No. 1 gear shift head to the No. 1 gear shift fork shaft.

  1. Using a 5 mm pin punch and a hammer, install a new slotted spring pin to the No. 1 gear shift fork shaft.

    NOTICE:
    Do not tap the pin too deep.

    Standard depth:
    0 mm (0 in.) (from the end surface of the No. 1 gear shift head)



26. INSTALL FRONT SHIFT INNER LEVER


    P000601E17
  1. Apply adhesive 1324 to the 2nd and 3rd pitches from the tip of new bolt.
    Text in Illustration 
    *1
    Adhesive 1324



    C257329
  1. Install the front shift inner lever to the shift shaft with a new bolt.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }



27. INSTALL NO. 1 SHIFT INTER LOCK BLOCK


    C262544
  1. Install the No. 1 shift inter lock block to the shift shaft.



28. INSTALL SHIFT SHAFT


    C258446
  1. Install the shift shaft and No. 1 shift inter lock block by sliding them.



29. INSTALL NO. 1 EXTENSION HOUSING OIL RECEIVER PIPE


    C257037
  1. Install the straight pin.



    C257036E01
  1. Install the No. 1 extension housing oil receiver pipe and stopper plate with a new bolt.
    Text in Illustration 
    *1
    No. 1 Extension Housing Oil Receiver Pipe End

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Confirm that the end of No. 1 extension housing oil receiver pipe is properly fitted in the groove.



30. INSTALL NO. 2 EXTENSION HOUSING OIL RECEIVER PIPE


    C257034
  1. Install the No. 2 extension housing oil receiver pipe.



31. INSTALL TRANSMISSION EXTENSION HOUSING OIL SEAL


    C257319E01
  1. Apply MP grease to the lip of the new transmission extension housing oil seal.

  1. Using SST and a hammer, install a new transmission extension housing oil seal.

    SST
    09325-20010  

    Installation depth:
    0.1 to 1.1 mm (0.00394 to 0.0433 in.) (from the end surface of the transmission extension housing sub-assembly)

    NOTICE:
    Do not damage the lip of the transmission extension housing oil seal.



32. INSTALL EXTENSION HOUSING DUST DEFLECTOR


    C257320E01
  1. Using SST and a hammer, install a new extension housing dust deflector.

    SST
    09950-60020   (09951-00750)
    09950-70010   (09951-07100)

    HINT:
    Make sure to tap it until it touches the transmission extension housing sub-assembly.



33. INSTALL EXTENSION HOUSING REAR OIL SEAL


    C257321E01
  1. Using SST and a hammer, install a new extension housing rear oil seal.

    SST
    09612-70100   (09612-07210)

    Installation depth:
    1.0 to 2.0 mm (0.0394 to 0.0787 in.) (from the end surface of the transmission extension housing sub-assembly)

    NOTICE:
    Do not damage the lip of the extension housing rear oil seal.

  1. Apply MP grease to the lip of the extension housing rear oil seal.



34. INSTALL TRANSMISSION EXTENSION HOUSING SUB-ASSEMBLY


    C257322
  1. Apply seal packing 1281 continuously to the transmission extension housing sub-assembly as shown in the illustration.
    Text in Illustration 
    V100143
    Seal Packing 1281

    NOTICE:
    Install it within 10 minutes of the seal packing application.



    C257030E02
  1. Install the transmission extension housing sub-assembly and clamp with 8 new bolts.
    Text in Illustration 
    *1
    clamp

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. Be sure to install the transmission extension housing sub-assembly while the transmission is in neutral.
    2. Make sure to align the knock pin with the hole securely.



    C257029
  1. Install a new bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



35. INSTALL HOLDER


    C257028
  1. Using a 27 mm deep socket wrench, install a new holder, compression spring and lock ball pin.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



36. INSTALL LOCK BALL PIN


    C257027
  1. Using a 10 mm hexagon socket wrench, install a new head straight screw plug, compression spring and lock ball pin.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



37. INSTALL WIRE HARNESS CLAMP BRACKET


    C257298
  1. Install the wire harness clamp bracket with a new bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



38. INSTALL NEUTRAL POSITION SWITCH ASSEMBLY


    C257025
  1. Using a 19 mm union nut wrench, install the neutral position switch assembly and a new gasket.

    Torque:
    32 N*m{ 329 kgf*cm , 24 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



    C257024
  1. Engage the clamp and connect the neutral position switch assembly wire.



39. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    C257023
  1. Using a 19 mm union nut wrench, install the back-up light switch assembly and a new gasket.

    Torque:
    32 N*m{ 329 kgf*cm , 24 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



    C266431E01
  1. In the order indicated in the illustration, engage the 3 clamps in place, and connect the back-up light switch assembly wire and neutral position switch assembly wire.

    HINT:
    Install the wire harness so that there is slack on the connector side.



40. INSTALL RELEASE FORK SUPPORT


    C258508
  1. Using a 19 mm deep socket wrench, install the release fork support to the clutch housing.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



41. INSTALL MANUAL TRANSMISSION DRAIN PLUG


    C257297
  1. Install the manual transmission drain plug with a new gasket to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



42. INSTALL MANUAL TRANSMISSION FILLER PLUG


    C257296
  1. Install the manual transmission filler plug with a new gasket to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }