Home › Drivetrain ยท TL70 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT THRUST CLEARANCE


    C257060E01
  1. Using a feeler gauge, measure the thrust clearance of the 1st gear, 2nd gear and reverse gear.
    Text in Illustration 
    *a
    Reverse gear thrust clearance
    *b
    2nd gear thrust clearance
    *c
    1st gear thrust clearance

    Standard Clearance:
    Gear
    Standard clearance mm (in.)
    Maximum clearance mm (in.)
    1st gear
    0.15 to 0.40 (0.00590 to 0.0157)
    0.40 (0.0157)
    2nd gear
    0.10 to 0.45 (0.000394 to 0.0177)
    0.45 (0.0177)
    Reverse gear
    0.10 to 0.45 (0.000394 to 0.0177)
    0.45 (0.0177)

    HINT:
    If the clearance exceeds the maximum, replace the corresponding gear, transmission clutch hub, needle roller bearing and output shaft with a new ones.



2. INSPECT RADIAL CLEARANCE


    C257061E01
  1. Using a dial indicator, measure the radial clearance of the 1st gear, 2nd gear and reverse gear.
    Text in Illustration 
    *a
    Reverse gear radial clearance
    *b
    2nd gear radial clearance
    *c
    1st gear radial clearance

    Standard Clearance:
    Gear
    Standard clearance mm (in.)
    Maximum clearance mm (in.)
    1st gear
    0.015 to 0.066 (0.000590 to 0.00260)
    0.066 (0.00260)
    2nd gear
    0.015 to 0.066 (0.000590 to 0.00260)
    0.066 (0.00260)
    Reverse gear
    0.015 to 0.066 (0.000590 to 0.00260)
    0.066 (0.00260)

    HINT:
    If the clearance exceeds the maximum, replace the corresponding gear, needle roller bearing and output shaft with a new ones.



3. REMOVE REVERSE GEAR


    C257062
  1. Using a snap ring expander, remove the shaft snap ring.



    C257063E01
  1. Using SST and a press, remove the No. 3 transmission clutch hub, No. 3 transmission hub sleeve, reverse gear, No. 3 synchronizer ring and reverse gear bearing from the output shaft.

    SST
    09950-00020  
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)



4. REMOVE NO. 3 TRANSMISSION HUB SLEEVE


    C257064
  1. Remove the No. 3 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the No. 3 transmission clutch hub.

    NOTICE:
    1. Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.
    2. Do not deform the No. 1 synchromesh shifting key spring.

    HINT:
    During this operation, keep intact the No. 3 transmission clutch hub and No. 1 synchromesh shifting key.



5. REMOVE 6TH GEAR


    C257065
  1. Using 2 screwdrivers and a hammer, remove the shaft snap ring.



    C257066E01
  1. Using SST and a press, remove the 6th gear.

    SST
    09950-00020  



6. REMOVE 1ST GEAR


    C266438E01
  1. Using SST and a press, remove the rear output shaft bearing, 1st gear and 1st gear bearing inner race.

    SST
    09950-00020  



    C266439
  1. Remove the 1st gear needle roller bearing, 1st shift restrict ball and No. 1 synchronizer ring set.



7. REMOVE 2ND GEAR


    C257069E01
  1. Using SST and a press, remove the 2nd gear, No. 1 transmission clutch hub and 2nd gear needle roller bearing from the output shaft.

    SST
    09950-00020  



8. REMOVE NO. 1 SYNCHRONIZER RING SET
  1. Remove the No. 1 synchronizer ring set.



9. REMOVE NO. 1 TRANSMISSION HUB SLEEVE


    C257070
  1. Remove the No. 1 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the No. 1 transmission clutch hub.

    NOTICE:
    1. Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.
    2. Do not deform the No. 1 synchromesh shifting key spring.

    HINT:
    During this operation, keep the No. 1 transmission clutch hub and No. 1 synchromesh shifting key intact.