Home › Drivetrain ยท TL70 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL REVERSE GEAR


    C257082
  1. Apply manual transmission gear oil to the mounting point of the output shaft, reverse gear bearing and inside surface and taper cone of the reverse gear.

  1. Install the reverse gear bearing and reverse gear to the output shaft.



2. INSTALL NO. 3 TRANSMISSION HUB SLEEVE


    C321947E01
  1. Apply manual transmission gear oil to the moving parts of the No. 3 transmission clutch hub.
    Text in Illustration 
    *1
    No. 3 Transmission Clutch Hub
    *2
    No. 3 Transmission Hub Sleeve
    *3
    Ball
    *4
    No. 1 Synchromesh Shifting Key
    *5
    No. 1 Synchromesh Shifting Key Spring
    V100135
    Front Side

  1. As shown in the illustration, install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub. And install the 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs all together, and then install the 3 balls.

    HINT:
    1. Install the ball while holding down the No. 1 synchromesh shifting key spring.
    1. After the installation, let the No. 1 synchromesh shifting key spring settle down.



3. INSTALL NO. 3 TRANSMISSION CLUTCH HUB


    C257083E01
  1. Install the No. 3 synchronizer ring to the reverse gear.

  1. Using SST and a press, install the No. 3 transmission clutch hub.

    SST
    09309-37010  

    HINT:
    1. Align the No. 3 transmission clutch hub and the No. 3 synchronizer ring so that they can fit together.
    2. After the No. 3 transmission clutch hub is installed, check that the No. 3 synchronizer ring moves in the thrust direction.
    1. Make sure to press fit the No. 3 transmission clutch hub until it touches the output shaft.



4. INSTALL SHAFT SNAP RING (for No. 3 transmission clutch hub)


    C257084
  1. Select a shaft snap ring that is suitable to retain the specific thrust clearance between the No. 3 transmission clutch hub and shaft snap ring.

    Standard clearance:
    0 to 0.1 mm (0 to 0.00394 in.)

    HINT:
    Select the thickest shaft snap ring possible for installation.

    Shaft Snap Ring Thickness 
    Part No.
    Thickness mm (in.)
    Mark
    SU003-03581
    1.80 (0.07086)
    A
    SU003-03582
    1.85 (0.07283)
    B
    SU003-03583
    1.90 (0.07480)
    C
    SU003-03584
    1.95 (0.07677)
    D
    SU003-03585
    2.00 (0.07874)
    E
    SU003-03586
    2.05 (0.08070)
    F

  1. Using a snap ring expander, install a new shaft snap ring to the output shaft.



5. INSTALL 2ND GEAR


    C257085
  1. Apply manual transmission gear oil to the mounting point of the output shaft, 2nd gear needle roller bearing and inside surface and taper cone of the reverse gear.

  1. Install the 2nd gear needle roller bearing and 2nd gear to the output shaft.



6. INSTALL NO. 1 TRANSMISSION HUB SLEEVE


    C321945E01
  1. Apply manual transmission gear oil to the moving parts of the No. 1 transmission clutch hub.
    Text in Illustration 
    *1
    No. 1 Transmission Clutch Hub
    *2
    No. 1 Transmission Hub Sleeve
    *3
    Ball
    *4
    No. 1 Synchromesh Shifting Key
    *5
    No. 1 Synchromesh Shifting Key Spring
    V100135
    Front Side

  1. As shown in the illustration, install the No. 1 transmission hub sleeve to the No. 1 transmission clutch hub. And install the 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs all together, and then install the 3 balls.

    HINT:
    1. Install the ball while holding down the No. 1 synchromesh shifting key spring.
    1. After the installation, let the No. 1 synchromesh shifting key spring settle down.



7. INSTALL NO. 1 TRANSMISSION CLUTCH HUB


    C266440
  1. Align and install the No. 1 synchronizer ring set (for 2nd gear) in the position, as shown in the illustration.

    HINT:
    1. Align the middle ring claw with the groove in the 2nd gear.
    2. Align the inner ring claw with the groove in the outer ring.



    C257087E01
  1. Using SST and a press, install the No. 1 transmission clutch hub.

    SST
    09309-35010  
    09631-12090  

    HINT:
    1. Align the No. 1 transmission clutch hub and the No. 1 synchronizer ring set (for 2nd gear) so that they can fit together.
    2. After the No. 1 transmission clutch hub is installed, check that the No. 1 synchronizer ring set (for 2nd gear) moves in the thrust direction.
    1. Make sure to press fit the No. 1 transmission clutch hub until it touches the output shaft.



    C257088
  1. Align and install the No. 1 synchronizer ring set (for 1st gear) in the position, as shown in the illustration.

    HINT:
    1. Align the outer ring claw with the groove in No. 1 transmission clutch hub.
    2. Align the inner ring claw with the groove in the outer ring.



8. INSTALL 1ST GEAR


    C257089E01
  1. After the output shaft is installed, apply manual transmission gear oil to the mounting point of the output shaft, needle roller bearing inner race, and inside surface and taper cone of the 1st gear.

  1. Install the 1st shift restrict ball, 1st gear, 1st gear needle roller bearing and 1st gear bearing inner race to the output shaft.
    Text in Illustration 
    *1
    1st Shift Restrict Ball

    HINT:
    Align the middle ring claw with the groove in the 1st gear.



9. INSTALL REAR OUTPUT SHAFT BEARING


    C266541E01
  1. Using SST and a press, as shown in the illustration, install the rear output shaft bearing.
    Text in Illustration 
    *1
    Rear Output Shaft Bearing
    V100135
    Front Side

    SST
    09309-35010  
    09316-60011   (09316-00021)

    HINT:
    Make sure to press fit the rear output shaft bearing until it touches the 1st gear bearing inner race.



10. INSTALL 6TH GEAR


    C257091E01
  1. Using SST and a press, install the 6th gear.

    SST
    09309-35010  

    HINT:
    Make sure to press fit the 6th gear until it touches the rear output shaft bearing.



11. INSTALL SHAFT SNAP RING (for 6th gear)


    C257092
  1. Select a shaft snap ring that is suitable to retain the specific thrust clearance between the 6th gear and shaft snap ring.

    Standard clearance:
    0 to 0.11 mm (0 to 0.00433 in.)

    HINT:
    Select the thickest shaft snap ring possible for installation.

    Shaft Snap Ring Thickness 
    Part No.
    Thickness mm (in.)
    Mark
    SU003-03564
    2.67 (0.10511)
    A
    SU003-03565
    2.73 (0.10748)
    B
    SU003-03566
    2.79 (0.10984)
    C
    SU003-03567
    2.85 (0.11220)
    D
    SU003-03568
    2.91 (0.11456)
    E
    SU003-03569
    2.97 (0.11692)
    F
    SU003-03570
    3.03 (0.11929)
    G
    SU003-03571
    3.09 (0.12165)
    H
    SU003-03572
    3.15 (0.12401)
    J
    SU003-03573
    3.21 (0.01053)
    K
    SU003-03574
    3.27 (0.12874)
    L

  1. Using a brass bar and hammer, install a new shaft snap ring to the output shaft.