Home › Drivetrain ยท TL70 MANUAL TRANSMISSION / TRANSAXLE › COUNTER GEAR

COUNTER GEAR > DISASSEMBLY

for Preparation Click here



1. INSPECT THRUST CLEARANCE


    C257094E01
  1. Using a feeler gauge, measure the thrust clearance of the counter shaft 3rd gear and counter shaft 4th gear.
    Text in Illustration 
    *a
    Counter shaft 4th gear thrust clearance
    *b
    Counter shaft 3rd gear thrust clearance
    Standard Clearance 
    Gear
    Standard clearance mm (in.)
    Maximum clearance mm (in.)
    Counter shaft 3rd gear
    0.10 to 0.35 (0.00393 to 0.0138)
    0.35 (0.0138)
    Counter shaft 4th gear
    0.10 to 0.35 (0.00393 to 0.0138)
    0.35 (0.0138)

    HINT:
    If the clearance exceeds the maximum, adjust it with the 4th inner race thrust washer.



2. INSPECT RADIAL CLEARANCE


    C257095E01
  1. Using a feeler gauge, measure the radial clearance of the counter shaft 3rd gear and counter shaft 4th gear.
    Text in Illustration 
    *a
    Counter shaft 4th gear radial clearance
    *b
    Counter shaft 3rd gear radial clearance
    Standard Clearance 
    Gear
    Standard clearance mm (in.)
    Maximum clearance mm (in.)
    Counter shaft 3rd gear
    0.015 to 0.068 (0.000590 to 0.00268)
    0.068 (0.00268)
    Counter shaft 4th gear
    0.065 to 0.115 (0.002559 to 0.00453)
    0.115 (0.00453)

    HINT:
    If the clearance exceeds the maximum, replace the corresponding gear and needle roller bearing or 4th gear bearing inner race all together with a new ones.



3. REMOVE FRONT COUNTER GEAR BEARING


    C257096
  1. Using a snap ring expander, remove the shaft snap ring.



    C257097E01
  1. Using SST and a press, remove the front counter gear bearing.

    SST
    09950-00020  
    09950-60010   (09951-00230)
    09950-70010  



4. REMOVE COUNTER DRIVE GEAR


    C257098
  1. Using a snap ring expander, remove the shaft snap ring.



    C257099E01
  1. Using SST and a press, remove the counter drive gear.

    SST
    09950-00020  
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)



5. REMOVE COUNTER SHAFT 4TH GEAR


    C257100
  1. Using a snap ring expander, remove the shaft snap ring, and then remove the 4th washer retaining ring and 4th inner race thrust washer.



    C257101
  1. Using a screwdriver, pry the 4th gear bearing inner race and turn it counterclockwise along the gear, and remove the 4th gear bearing inner race.



    C257102
  1. Remove the counter shaft 4th gear and No. 1 synchronizer ring.



6. REMOVE COUNTER SHAFT 3RD GEAR


    C257103E01
  1. Using SST and a press, remove the No. 2 transmission clutch hub, counter shaft 3rd gear, No. 3 synchronizer ring set and needle roller bearing.

    SST
    09950-00020  



7. REMOVE NO. 2 TRANSMISSION HUB SLEEVE


    C257070
  1. Remove the No. 2 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the transmission clutch hub.

    NOTICE:
    1. Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.
    2. Do not deform the No. 1 synchromesh shifting key spring.

    HINT:
    During this operation, keep the No. 2 transmission clutch hub and No. 1 synchromesh shifting key intact.